Wifi Ethernet-Bridge WTP-5000

Trois modèles sont disponible:

  • WTP-5000: jusqu'à 5 km distance, jusqu'à 54 MBit/s, prêt à l'usage, 349.00 € par côté
  • Mini WTP-5000: jusqu'à 800m distance, jusqu'à 150 MBit/s, prêt à l'usage, 212.50 € par côté
  • Nano WTP-5000: jusqu'à ~200m distance, jusqu'à 150 MBit/s, prêt à l'usage, 199.00 € par côté

Pont Ethernet Wifi Maxi-WTP-5000

Maxi-WTP-5000 Bridge

Ideal product to connect remote buildings, branch offices without network connection to the internet. Or integrate outlying buildings quickly and secure into your local network. The maximum distance is up to 5km with a free line of sight.

The Maxi-WTP-5000 is a 2x 24 dBi directional antenna with built-in Ethernet bridge. The device is pre configured for transparent operations (default SSID and WPA encryption). For point-to-point operation no further configuration is necessary! Just mount it outside of the building, connect to your local computer or network and go.

The bridge acts like a 'wireless cable', works independently of IP adresses of your local network and carries nearly any relevant protocols. Just like the outlying computer were connected to you LAN with a cable. The maximum data rate is 300MBit/s. For maximum security the connection is encrypted via AES/CCMP, the authentication is done by WPA2.

The Maxi-WTP-5000 bridges could handle much more than simple bridge operation. The integrated board supports also the operation as a Wifi client unit, for example also for VLANs. The configuration is done by Telnet/ssh (recommended) or by a webbrowser or a supplied windows tool.

The WTP-bridges are installed in a solid weatherproof case. The allowed temperature range is from -30 to +70°C. A mast mount bracket is included in shipment. The case has a waterproof RJ-45 socket for connection of an ethernet cable (not included). Power supply is done over the ethernet cable (PoE) with the supplied adaptor and power supply (PoE not 802.11af compatible).

Attention - for bridge use you need one unit 'bridge' and one unit 'Client'.

Réference
18781.C Maxi-WTP-5000 5GHz Client 349.00 € Acheter Nouveau
18781.B Maxi-WTP-5000 5GHz Bridge 349.00 € Acheter Nouveau
Info frais de port
Download: Datasheet WTP-Bridge (PDF, DE/EN, 50KB)
Download: Installation Instructions WTP-Bridge, german only! (PDF, DE, 100KB)

Pont Ethernet Wifi miniature WTP-5000n 802.11n

mini-WTP-5000 wifi ethernet bridge Mini-WTP-5000 Bridge

Jusqu'à 800 m de distance, taux de transfert élevé grâce au protocole 802.11n.
Préconfiguré, utilisable immédiatement comme un 'long câble' ethernet !

Les nouveaux systèmes WTP-5000n disposent de la technologie la plus récente 802.11n, pour une connexion plus rapide et plus fiable. La connexion radio permet un débit d'environ 150 MBit/s et peut ainsi être utilisée pour des applications telles que VoIP, Webcams etc... La distance couverte est de 500 à 800 m. La vitesse de transmission effective dépend de la distance, de la situation locale et de la connexion cuivre.

Le boitier résiste aux intempéries et peut ainsi être monté en extérieur sur un mât à l'aide du matériel de montage fourni. La connexion requiert l'emploi d'un câble ethernet (non livré). L'alimentation électrique est fournie au travers du câble ethernet, l'alimentation DC est livrée. Savez que l'alimentation n'est pas compatible aux standard 802.3af ni 802.11at.

Le Mini WTP-Bridge est préconfiguré et prêt à l'emploi pour une connexion Wifi avec cryptage WPA2. Installez-le sur le mât, mettez-le sous tension, il est prêt. Le pont est transparent dans votre réseau et se comporte comme un simple câble ethernet.

Le boitier est de dimensions compactes avec un diamètre de 250 mm et une profondeur de 90 mm. Poids : 830 g

Pour la mise en service, il vous faut une extrêmité 'pont' et une 'client'

Contrairement aux modèles plus anciens, cet équipement ne peut pas être combiné avec le modèle WTP-5000 proposé ci-dessous.

Note:
Le câble ethernet doit disposer d'un connecteur le plus court possible. Le connecteurs moulés standards peuvent être trop longs, les connecteurs classiques à sertir conviennent parfaitement.

Pour des distances plus importantes, jusqu'à 5 km, il vous faut envisager un modèle plus conséquent tel que le Maxi-WTP-5000.

Réference
18783.C Mini-WTP-5000n 5GHz Client 212.50 € Acheter
18783.B Mini-WTP-5000n 5GHz Bridge 212.50 € Acheter
Info frais de port
Download: Datasheet WTP-Bridge (PDF, DE/EN, 50KB)
Download: Installation Instructions WTP-Bridge, german only! (PDF, DE, 100KB)

NANO-WTP

Nano-WTP-5000 Ethernet Wifi bridge Nano-WTP-5000 Ethernet Wifi bridge

If you want to transmit only 'across the street', then a smaller and thus cost-saving solution is sufficient.

The NANO-WTP has the same features like the MINI-WTP specified above, but a smaller and thereby less conspicuous antenna with only 140 mm diameter and respectively less gain.

However it works a couple of hundred meter far when in line of sight, in fact with great signals!

Réference
18785.C NANO-WTP, Client side (for remote building) 199.00 € Acheter
18785.B NANO-WTP, Bridge side (for building with LAN connection) 199.00 € Acheter
Info frais de port

Pieces de rechange WTP-Bridges

Réference
18790.PS POE Power Splitter for WTP-Bridge piece de rechange 18.50 € Acheter
RB-411 Mikrotik RB-411 Board 74.80 € Acheter
Info frais de port

FAQ WTP-5000 Bridge

  1. How many devices do I need for one link?

    Two, one Bridge, one Client.

  2. Which power consumption do the bridges have?

    Power consumption is 8 to 12 W at 24V supply voltage.

  3. What is the maximum cable length?

    The WTP-5000 Bridges are connected wit ha standard Ethernet cable to your local switch or computer. Depending on the network structure this cable can be up to 100m long.

  4. Do I need special Ethernet cables?

    When installed permanently - yes. The cables should be UV resistant. Perhaps it's a good idea to install the cables into tubes or in the antenna mast.

  5. Does a regular RJ-45 fit through the supplied, weatherproof connection?

    Yes, except with the mini-WTP, which requires RJ45 connectors without plastic cap (crimp connectors). On the Maxi-WTP large professional connectors like telegärtner MFP8 can be too large.

  6. Does the bridge support the spanning tree protocol, so I can use the bridge as a backup link to the existing network??

    Yes, STP is supported.

  7. What about support for other functions like QoS, Trunking, packet filter (aka firewall), SNMP, Routing etc?

    Yes, mayn of these functions are supported (except trunking). The board used in these bridges is quite complex and offers many more functions than used by the bridge. The problem is: We can support you only with the standard configuration (except changed password, IP addresses etc.). If you use further functions of the board we are unable to support you technically.

  8. How do I change the IP address, the password, the radio channel, the WPA passphrase etc.?

    The board used in the bridge support configuration by Telnet/SSH or brwoser interface or by a supplied windows tool. We recommend the configuration by SSH (command line).

  9. Does the bridge retain it's configuration also at a power outage?

    Yes.

  10. Does this bridge require a special radio permit?

    No, at least not in Germany. It uses regular Wifi systemns, but the bridge is configured for the German regulatory domain. It might be necessary to change the bridge settings to our country for compliance with your local rules.

  11. Can I connect with multiple Wifi clients to one bridge?

    No, unfortunately that's not possible with the currently employed softwware revision (Mikrotik RouterOS Level 3).

  12. Can I connect two separate network segments with the same IP address range with this bridge?

    Yes, that's just what the WTP-5000 is made for.