LDG Automatic antenna tuners

Here you will find:

LDG YT-1200 Automatic tuner for FT-450/950/1200/3000

YT-1200

Yaesu radios are very popular and so LDG is working to offer a suitable tuner for each radio. And even when the Yaesu radios do have a built in tuner, there is nothing which coulnd't be improved.

The LDG YT-1200 is suitable for use with the FT-450(D), FT-950, FT-DX1200 and FT-DX3000. In contrast to the built-in tuners LDG tuners offer various benefits: less power consumption though latching relays, larger tuning range (typ. 4 to 1000 Ω) and faster tuning. Supplied with the tuner is a cable which provides power and CAT data from the radio. This allows for very convenient tuning - just press the 'Tune' button on the tuner. The radio will be switched to CW, the power is reduced, then the tuning process starts. After tuning the radio is reverted to it's previous mode and power setting.

The CAT interface of the radio is duplicated on the tuner, so you don't loose any functionality. You can continue to use your favorite software with your radio and the tuner at the same time.

This tuner has one coaxial connector for one coax-fed antenna - dipoles, verticals, beams, whatever. Wire antennas would require an optional balun.

For further technical details please see the Comparision table of LDG Tuners at the end of this page.

Order No.
YT-1200 LDG Tuner for FT-450, FT-450AT, FT-950 298.00 € Buy now
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

Z-817 Automatic Antenna Tuner


LDG Z-817

The Z-817 is the ultimate autotuner for QRP radios including the Yaesu FT-817(D). The Z-817 interfaces to the CAT port (ACC) on the back of the FT-817 radio with the provided cable. Tuning could not be simpler; one button push on the tuner is all that is needed and the Z-817 takes care of the rest. It will switch to PKT mode, transmit a carrier, tune the tuner, then restore the radio to the previous mode! 2000 memories cover 160 through 6 meters.

Of course, the Z-817 will also function as a general purpose antenna tuner with other QRP radios. Just transmit a carrier and press the tune button on the tuner. The Z-817 is powered by four AA internal Alkaline batteries (not included), so there are no additional cables required to use the Z-817. Latching relays are used so that power consumption is Zero when not tuning allowing a set of batteries to last about one year.

  • Technical Data
  • RF Power 0.1 to 20 watts SSB, CW and digital modes
  • Latching relays for ultra low power consumption
  • Battery operated 4 x 1.5V Alkaline AA (not included)
  • Built-in CAT port interface. CAT thru port for computer connection.
  • 2000 memories when used with FT-817 interface (200 memories for other radios)
  • 1.8 to 54 MHz coverage
  • Tunes 6 to 600 Ω (about 10:1 SWR range). 16 to 150Ω on 6m (about 3:1)
  • SO-239 in and out connections for dipoles, verticals, beams, G5RV, OCF, Cobra, ect.
  • Dimensions: 120 x 43 x 130 (WHD). Weight: approx. 300 g (without batteries).

Included in shipment is one CAT cable for Yaesu (30cm).

Order No.
Z-817 LDG Antenna Tuner 20 W 149.00 € Buy now
LDG-Y-CAT Control Cable Yaesu FT-857/897, as supplied 11.40 € Buy now
Info freight charges

Suitable batteries: Ansmann maxE rechargeable batteries! 2100mAh capacity, very low self-discharge. Comes fully charged, ready for immediate use.

Order No.
MAXE-4AA 14.80 € Buy now
Info freight charges

LDG KT-100 Automatic tuner for Kenwood.

LDG KT-100 LDG KT-100

The KT-100 is a external Tuner for Kenwood Radios with Tuner Socket.
The KT-100 does everything that is needed for the tuning alone. You only need to press the Tune button on the transceiver and the tuner will does the rest Specifically, this means the transceiver is controlled to 10 W back, switched to CW and sent a carrier.

The Tuner is connecting with the supplied cable directly to the tuner socket. The power supply is also trough this connection.

Special TS-480HX: If an external tuner is connected to the Kenwood TS-480HX transceiver, the output power is automatically throttled to 100W.

Further technical details:

  • Frequency range 1.8 to 54.0 MHz
  • 0,1 to 125 Watt (SSB und CW), 100 W on 6m
  • Tuning time between 0.1 and 6 seconds for new frequencies, ca. 0.1 sec when tuning from memory
  • Tuning range 4 to 800 Ω (16 to 150 Ohm on 6m), 4 to 3200 Ω with optional 4:1 balun
  • Tunes any kind of coax-fed antennas: Dipoles, Verticals, Beams etc.
  • Optional external balun enables you to tune random wires, long wires or twin ladder fed antennas
  • Control cable (35cm) included
LDG KT-100 Rear view
Order No.
KT-100 for all Kenwood with Tunersocket 217.00 € Buy now
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

LDG IT-100 Automatic antenna tuner for IC-7000 / IC-706 etc.

LDG YT-100 Automatic antenna tuner for FT-100/FT-857/FT-897.

LDG IT-100 LDG IT-100
LDG YT-100 LDG YT-100
LDG IT-100 Rear

The operation of the tuner is done very conveniently by the push button on the tuner, with the IT-100 alternatively by the "Tune" button on the radio. A longer push starts a new tuning cycle, a short push switches to "bypass". With 2000 memories the tuners find once tuned frequencies very fast, for new frequencies the tuning takes max. 6 seconds. The tuners match a SWR from 10:1 (3:1 on 6m) and therefore a much wider tuning range than many other tuners. Two LEDs show the "SWR too high" error and the tuning process.

Both devices are connected with the supplied cable (35cm long) to the CAT (Yaesu) or Tuner (Icom) socket of the radio, which also supplies them with power. This reduces the required cabling to an absolute minimum.

The IT-100 tuner supports all Icom radios with a 4-pin tuner socket (i.e. IC-706Mk2G, IC-718, IC-746, IC-7400, IC-756Pro3 etc.). The size of the tuner is 17x17x4cm, the weight is 750g.
The YT-100 is intended for use with the Yaesu FT-100, FT-857 and FT-897. The tuner has a size of 20x9x4.6cm and has a free CAT socket on the rear, allowing you to connect radio and computer at the same time.

  • Technical Data
  • Frequency range 1.8 to 54.0 MHz
  • 0,1 to 125 Watt (SSB und CW), 100 W on 6m
  • Tuning time between 0.1 and 6 seconds for new frequencies, ca. 0.1 sec when tuning from memory
  • Tuning range 4 to 800 Ω (16 to 150 Ohm on 6m), 4 to 3200 Ω with optional 4:1 balun
  • Tunes any kind of coax-fed antennas: Dipoles, Verticals, Beams etc.
  • Optional external balun enables you to tune random wires, long wires or twin ladder fed antennas
  • Control cable (35cm) included
Order No.
IT-100 for all Icom with 4pin tuner socket 199.00 € Buy now
YT-100 for Yaesu FT-100, FT-857, FT-897 217.00 € Buy now
LDG-I7-ACC Controlcable for IT-100 / AT-7000 13.80 € Buy now
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

RT/RC100 Automatic Outdoor Antenna Tuner with Remote Control

RT-100MK2 Outdoor antenna tuner

The LDG RT-100MK2 is a 100 W automatic antenna tuner for split installation.
The tuner can be installed directly at the antenna and is supplied with power via the coaxial cable. The tuner is designed for unbalanced antennas and has beside the two PL jacks for input and output, an additional screw for connecting an ground wire.

The RT-100MK2 includes a remote control unit.
This unit has a remote power supply with bias-Tee's to power the remote tuner RT-100 directly via the coaxial cable. In addition, the tuning can be triggered manually, also. Unintended tuning can be prevented by "blocking" the RC-100 tuner. A status LED provides reliable information about the operating state.

  • Technical Data
  • Frequency range 1.8 to 54.0 MHz
  • 0,1 to 125 Watt (SSB und CW), 100 W on 6m
  • Tuning time between 0.1 and 6 seconds for new frequencies, ca. 0.1 sec when tuning from memory
  • Tuning range 4 to 800 Ω (16 to 150 Ohm on 6m), 4 to 3200 Ω with optional 4:1 balun
  • Tunes any kind of coax-fed antennas: Dipoles, Verticals, Beams etc.
  • Weight 500g
Order No.
RT-100MK2 LDG Automatic Outdoor Antenna Tuner 299.00 € Buy now
Info freight charges

RT/RC-600 Automatic Outdoor Antenna Tuner with Remote Control

RT-600 Outdoor antenna tuner

Same as RT-100MK2 (see above), but 600 Watt. With remote control unit.

Order No.
RT-600 LDG Automatic Outdoor Antenna Tuner 539.00 € Buy now
Info freight charges

Z-11Pro-II Antenna Tuner

Bild Z-11Pro-II

LDG Z-11Pro-II
  • 0.1 to 125 watt power range (SSB and CW), 100 W on 6M
  • Easy to read LED display for SWR and status
  • 8000 3-D memories for instantaneous band changing
  • Tuning time: 0.1 to 6 seconds full tune, 0.1 seconds memory tune
  • Selectable user parameters: Auto/Semi, threshold, and more
  • 1.8 to 54.0 MHz coverage. Built-in frequency sensor
  • Tunes 6 to 1000 Ω loads (16 to 150 on 6M), 6 to 4000 Ω with optional 4:1 Balun
  • For Dipoles, Verticals, Vs, Beams or and Coax Fed Antenna
  • Optional external Balun allows tuning of random length, long wire or ladder line fed antennas
  • Optional interfaces for Icom, Alinco, Kenwood and Yaesu available
  • Power requirements: 8 to 16 volts DC at 300 mA Max. 25 uA standby current
  • User installable battery holder (included)
  • Small Size Enclosure: 7.7" x 5.0" x 1.5". Weight: 1.5 pounds

The Z-11Pro-II uses LDG's state-of-the-art processor-controlled Switched-L tuning network. It will match dipoles, verticals, inverted-Vs or virtually any coax-fed antenna. With an optional LDG balun, it will also match longwires or antennas fed with ladder-line.

The Z-11Pro-II has 8,000 memories in LDG's exclusive "3-D Memory" array, automatically storing tuning configurations for each frequency and band as you use them, for each of four antennas on the single RF port. Frequency sensing circuitry lets the Z-11Pro-II "know" your operating band and frequency. Whenever you transmit on or near a frequency you've used before, the Z-11Pro-II retunes from memory almost instantly (even in SSB!). Memories are retained indefinitely.

Rugged and easy-to-read LEDs indicate SWR and status. The Z-11Pro-II uses latching relays which retain the tuned configuration even when powered down; current draw when not tuning is effectively zero.

For maximum flexability, the user has the choice of many battery options; internal or external. There are solder pads on the PC board for the user to install a battery pack (included) that best suits their needs. You could use 6-8 AAs and get several years of operation. If weight is a factor (for back packing), then three Lithium AAs will last about a year. If you just need a few months, the Z-11Pro-II will operate fine off a single 9V battery.

Control from the front panel is simple and straightforward; just press Tune while transmitting, and the Z-11Pro-II will begin a tuning cycle. The Z-11Pro-II will even tune while you talk on AM or SSB. Although not required, optional interfaces are available for most Icom, Kenwood, Yaesu and Alinco transceivers. With the interface, a single button-press transmits a carrier, executes a tuning cycle and returns the radio to its original power and mode.

Z-11Pro-II Rear
Order No.
Z-11PRO-II LDG Antenna Tuner 199.00 € Buy now
LDG-Y-ACC Control Cable for Yaesu FT-857/897, FT-891 11.40 € Buy now
LDG-I-ACC Control Cable for Icom Tuner socket 13.80 € Buy now
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

AT-100pro2/AT-200pro2 Desktop antenna tuner

Bild LDG AT-100pro

The LDG AT-100Pro2 and AT-200pro2 are desktop tuners which cover all frequencies from 1.8 to 54 MHz, and will automatically match your antenna in no time. It features a two-position antenna switch, allowing you to switch instantly between two antennas. The AT-100Pro2 requires just 1 watt to operation (5 W for AT-200pro2), but will handle up to 125 watts, making it suitable for everything from QRP up to a typical 100 watt transceiver. The AT-200pro2 handles up to 200 W on HF, max. 100 W on 6m, minimum tuning power for the AT-200pro2 is 5W.
Each tuner includes over 2,000 memories for each antenna, automatically storing tuning configurations for each frequency and band as you use them. Frequency sensing circuitry lets the AT-100Pro2/AT-200pro2 "know" your operating band and frequency. Whenever you transmit on or near a frequency you've used before, the tuner can retune from memory almost instantly: Tuning time is 0.2 sec for memory tune, 0.5 to 6 seconds for full tune.
LDG AT-100pro Rear Rugged and easy-to-read LED bargraphs show power and SWR, and a Function key on the front panel allows you to access data like mode and status.
The tuners will match dipoles, verticals, inverted-Vs or virtually any coax-fed antenna. With an optional balun, you can also use longwires or antennas fed with ladder-line. Tunes 6 to 1000 Ω loads (16 to150 on 6m), 6 to 4000 Ω with optional 4.1-balun.
Control from the front panel is simple and straightforward; just press Tune while transmitting a carrier, and the tuner will begin an automatic tuning cycle. For even more comfortable operation control cables for Icom and Yaesu transceivers is offered as an option. With the cable, a single button-press transmits a carrier, executes a tuning cycle and returns the radio to its original power and mode.

Power requirements: 11 to 16 volts DC at 500 mA max., dimensions: AT-100pro2 19 x 14 x 5 cm. AT-200pro2: 24.7 x 18 x 5cm, Weight: 0,8 Kg. A DC power cable is included.

Order No.
AT-100PRO2 LDG Antenna Tuner 100 W 255.00 € Buy now
AT-200PRO2 LDG Antenna Tuner 200 W 286.00 € Buy now
LDG-Y-ACC Control Cable FT-857/897, FT-891 11.40 € Buy now
LDG-I-ACC Control Cable Icom Tuner socket 13.80 € Buy now
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

AT-600pro2 Automatic Tuner 600W

The LDG AT-600Pro2 closes the gap for mid-range power levels. The tuner allows a maximum power on shortwave (1.8 to 30MHz) of 600 W in SSB and CW, max. 300 W in RTTY. On 6m (50 to 54MHz) a maximum power of 250 W is possible. The AT-600Pro2 uses the proven LDG switched L network, controlled by a micro processor. This results in automatic tuning within a few seconds. The matching ranges from 6 to 800Ω on shortwave (16 to 150Ω on 6m). This corresponds to an SWR of approx 10:1 which is transformed to approx. 1.5:1.

The LDG At-600Pro2 offers two selectable coaxial antenna connectors, suitable for any kind of antenna like yagis, dipoles, verticals etc. Longwire, random wire or ladder-line fed antennas can be tuned with an optional balun. Once found matches are stored, separately for each antenna connector, in 4000 memories. This speeds up the matching process considerably.

The front panels offer two LED bar graphs, one for power and one for SWR. A single LED shows which of the two antennas is selected. Easy to operate keys offer the prossibility to change the tuning manually, this is very useful in cases where you want to match the antenna without transmitting.

The LDG AT-600Pro2 has a size of 22 x 6 x 27cm (WxHxD) and weights approx. 1.5kg. As power supply the tuner requires 11 to 16V DC, max. 750mA. Included in shipment is a DC cable.

Optional control cables are also available. But please note that the automatic tune function, which these cable offer can lead to accidental tuning with high power, possibly destroying your amplifier or tuner. Always tune with low power!

The difference between the AT-600pro2 and the AT-600Pro is a connection for an optional external analog instrument (M-600).

AT-600Pro2
Order No.
AT-600PRO2 LDG At-600Pro2 Automatic Tuner 600 W 410.00 € Buy now
LDG-Y-ACC Control Cable Yaesu FT-857/897, FT-891 11.40 € Buy now
LDG-I-ACC Control Cable Icom Tuner socket 13.80 € Buy now
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

Z-100PLUS Automatic antenna tuner

The Z-100PLUS is an automatic antenna tuner useable for 1.8 to 54 MHz, for any transceiver with 0.1 to 125 Watt power SSB/CW (100 W FM, 30 W on 6m). The tuner is suitable for any unsymmetrically fed antenna (i.e. Beams, Dipoles, Groundplanes etc.). If the matching range is not sufficient, a 4:1 balun (symmetrical) or a MTFT balun (unsymmetrical) can be used (not included).

The tuner has 2000 memories which store settings for a once tuned frequency, when calling up the same frequency again the tuning lasts only some milliseconds. If no matching frequency is found tuning typically takes about 6 seconds.

Due to the use of latching relays the tuner requires only very little power (8 uA when stby)and is well suited for QRP/battery supplied operations. Power requirement during tuning is about 300mA. The Z-100Plus has two LEDs to show the current state (tuned etc.). Impedance matching range is 6 to 800 Ω, SWR from 10:1 (6m: 3:1), supply voltage required is 7 to 18V. Dimensions 140 x 140 x 38mm, weight ca. 400 gr. A DC cable is included.

Order No.
Z-100PLUS LDG Antenna Tuner 175.00 € Buy now
LDG-Y-ACC Control Cable Yaesu FT-857/897, FT-891 11.40 € Buy now
LDG-I-ACC Control Cable Icom Tuner socket 13.80 € Buy now
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

AT-897plus


Ideal for the FT-897 (but not only for this rig) the AT-897plus offers a wide matching range for coaxial fed antennas. The power for the AT-897plus is supplied over the CAT cable (included), a daisy-chained CAT interface on the rear of the tuner allows for other connections (i.e. PC).
To tune the AT-897plus a carrier in CW, FM or AM is required, with the push of thefront side btton the tuner tries to find a match. The required control cable between tuner and radio is included.
Due to the use of latching relays the AT-897plus requires only very little power in stby (some uA). The picture shows an AT-897 mounted to the side of a FT-897 (not included).

Order No.
AT-897PLUS LDG Antenna Tuner 217.00 € Buy now
LDG-Y-CAT Control Cable Yaesu FT-857/897, as supplied 11.40 € Buy now
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

LDG AT-1000pro2 automatic antenna tuner 1000 Watt

Fully automatic antenna matching with power up to 1000W! Controlled by a microprocessor the SWR is analyzed, a switched L network tuned faster than any manual control could do. Usually matches a SWR of 10:1 dowen to 1.5:1 within 3 seconds. Once found settings are stored in memory, resulting in even faster tuning when the same frequency is later tuned again. The easy t oread LED bar graphs show power and SWR. Tuning is done with low power, not while the PA is engaged!

To offer the same ease of use as with the other LDG tuners, the AT-1000pro2 has the following improvements over it's predecessor:

  • Two selectable antennas
  • 2000 memories for each antenna
  • Dedicated keys for manual fine tuning
AT-1000pro2
  • Technical Data
  • 1000 Watt max. power
  • Switched L Network
  • Bargraph for SWR
  • Tuning time 0.1 to 4 seconds, 3 seconds average, 0.2 sec near known frequencies
  • Power requirements: 11 to 15VDC, max. 1A
  • Two unsymmetric antenna connectors (PL), for symmetric antennas please use a 1:4 balun
  • Frequency range 1.8 to 54 MHz, Impedance from 6 to 1000 Ω (6 to 150 Ω on 6m)
  • Power ranges: 20 to 1000 W SSB, 750 W CW, 500 W Digital, 100 W on 6m
  • Suitable for dipoles, verticals, inverted V etc.
  • Dimensions: 25.4 x 28 x 7.6cm, Weight ca. 3 kg

M-1000 Analog Instrument for AT-1000Pro2

M-1000

New The M-1000 is intended for the AT-1000Pro2 and offers a beautiful and easy to read analog instrument. It shows the most important data at a glance. The power range is selectable between 100 and 1000W, the instrument shows either forward or reflected power or SWR. The power display can be switched between average and peak value.

Order No.
AT-1000PRO2 Tuner 597.00 € Buy now
M-1000 Analog instrument for AT-1000Pro2 149.50 € Buy now New
LDG-Y-ACC Control Cable Yaesu FT-857/897, FT-891 11.40 € Buy now
LDG-I-ACC Control Cable Icom Tuner socket 13.80 € Buy now
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

Control Cables LDG

The following control cables are offered by LDG or supplied with select tuners. With the exception of cable LDG-Y-ACC all cables serve to supply the tuner with power and accomodate the tune function.

LDG Kabel
Name Connector 1 Connector 2 for Tuner for Radio Function Price
LDG-Y-ACC 3.5 mm phone plug, Stereo 3.5 mm phone plug, Stereo Z-11Pro2, Z-100+, AT-100pro2,
AT-200pro2, AT-600pro2, AT-1000pro2
FT-857, FT-897, FT-891 New Tune 11.40 € Buy now
LDG-Y-CAT 8-pin MiniDIN 8-pin MiniDIN Z-817, AT-897+, YT-100 FT-100, FT-857, FT-897 Tune + Power 11.40 € Buy now
LDG-I-ACC Icom Tuner plug 3.5 mm phone plug
+ DC coaxial
Z11-Pro2, Z-100Plus, AT-100Pro2, AT-200Pro2, AT-600Pro2, AT-1000Pro2 all Icom with Tuner socket Tune + Power 13.80 € Buy now
LDG-I7-ACC Icom Tuner plug 6-pin MiniDIN IT-100 all Icom with Tuner socket Tune + Power 13.80 € Buy now
LDG-Kenwood Kenwood Tuner plug 7-pin MiniDIN KT-100 all Kenwood with Tuner socket Tune + Power -
LDG-FT847 9-pin D-Sub
8-pin MiniDIN
9-pin D-Sub
DC coaxial
YT-847 FT-847 Tune + Power -
LDG-IC450 9-pin D-Sub
8-pin MiniDIN
9-pin D-Sub
DC Coaxial
YT-450, YT-1200 FT-450 Tune + Power -

Coaxial HF Cables

Short coaxial cables to conect the radio to the tuner. LowLoss cable type H-155 with PL connectors on bith sides.

Order No.
40402.50CM PL/PL Cable H-155, 50cm 10.30 € Buy now
40402.01 PL/PL Cable H-155, 100cm 10.90 € Buy now
Info freight charges

LDG Tuner Comparision Table

Comparision Table LDG Tuner
  Z-817 Z-100+ Z-11Pro2 AT-897+ KT-100 RT-100 RT-600 YT-100 IT-100 YT-1200 YT-847 AT-100Pro2 AT-200Pro AT-600Pro AT-1000Pro2
Freq. Range [MHz] 1.8 - 54
Power 1.8 - 30MHz [W] 0.1 - 20 0.1 - 125 600 0.1 - 125 1 - 100 0.1 - 100 5 - 250 5 - 600 20 - 1000
Max. Power 6m [W] 20 30 100 600 100 250 250
Antenna connectors 1x PL 2x PL
Tuning Range [Ω] 6 - 600 6 - 800 6 - 1000 6 - 800 4 - 800 4 - 800 4 - 800 4 - 800 4 - 800 4 - 1000 4 - 1000 6 - 1000 6 - 800 6 - 800 6 - 800
Number of Memories 2000 4000 16000 4000 4000
Internal Battery possible Yes No
Ext. Supply Voltage [V] No 8 - 18 8 - 18 No (via CAT) No (via CAT) No (via CAT) No (via CAT) No (via CAT) No (via CAT) No (via CAT) No (via CAT) 11 - 16 11 - 16 11 - 16 11 - 16
Current Draw after Tune 0 < 25µA < 25µA < 25µA < 8mA < 8mA < 8mA < 8mA < 8mA < 8mA < 8mA < 8mA < 1A < 1A < 1A
On/Off Switch No No No No No No No No No No No No Yes Yes Yes
Latching relays Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes No No No
Manual Tuning Yes
Automatic Tuning No No Yes No No No No No No No No Yes Yes Yes Yes
Manual Tuning of L & C No No No No No No No No No No No Yes Yes Yes Yes
Display SWR 1 LED 1 LED 3 LEDs No 1 LED No No No 1 LED 1 LED 1 LED LED Bar LED Bar LED Bar LED Bar
Display Power No No No No No No No No No No No LED Bar LED Bar LED Bar LED Bar
Cable included 1x LDG-Y-CAT 1x DC 1x DC 1x LDG-Y-CAT 1x LDG-Kenwood - - 1x LDG-Y-CAT 1x LDG-I-ACC 1x LDG-IC450 1x DC 1x DC 1x DC 1x DC 1x DC