MiniVNA Analyser by Mini Radio Solutions

Mini-VNA Tiny Antenna Analyzer up to 3 GHz Nuovo!

mini-VNA Tiny mini-VNA Tiny
MINIVNA-TINY in the payload of a balloon mission for antenna measurements

The MiniVNA-TINY is a very compact antenna analyzer with USB connection. Remarkable is the very large frequency range from 1 to 3000 MHz. The MiniVNA-TINY is a network analyzer and does not only allow measurement of SWR and impdances of antennas. As a two-port system the MiniVNA-Tiny can be used for transmission measurements on band filters or amplifiers. The device works as a vectorial analzer, suitable to do typical quadrupole measurements of S11 and S21 parameters. The results can be displayed or stored as Smith diagram.

Due to the calibration with an optional calibration kit (open, short, load, see arrticle 21010.SMA) the measurement results are precise and easily reproducible. Impedance (Z) can be measured from 1 to 1000 Ω, the dynamic range is up to 70 dB. The analyser can be used as a low power HF generator as well. Power supply is done by the USB interface, an external power supply is not required. Software upgrades are also provided via the USB interface. The recommended software is 'VNA/J' the same software as already known from the other MinIVNA products. THis software is available for Windows, MAC and Linux, a new Android app is also available.

The Android app is called 'BlueVNA' and is available in the Google Play Store. The connection to the Android device is done by USB, you will require an OTG adaptor (not sold by WiMo).

Dati tecnici miniVNA-Tiny
Gamma di frequenze 1 – 3000 MHz
Impedance Range (Z) 1 – 1000 Ω
Output Power -6dBm @ 500 MHz
Dynamic Range up to 70 dB @ 500MHz
Connettores 2 × SMA
Power Consumption 370mA @5V (USB)
Peso 70 g
Misura 66 x 66 x 28mm
Ordine No.
MINIVNA-TINY miniVNA-Tiny 428.00 € Ordina
21010.SMA Calibration Kit (Open/Short/Load SMA) 21.00 € Ordina
21005.03 Attenuator 3 dB, 1 Watt, SMA 24.50 € Ordina
21005.06 Attenuator 6 dB, 1 Watt, SMA 24.50 € Ordina
21005.10 Attenuator 10 dB, 1 Watt, SMA 24.50 € Ordina
21005.20 Attenuator 20 dB, 1 Watt, SMA 24.50 € Ordina
40310.SM-SM Patch cable 2x SMA-plug, RG-316, length 30cm 16.10 € Ordina
40310.SMSM15 Patch cable 2x SMA-plug, RG-316, length 15cm 15.00 € Ordina
Info sui costi di spedizione

Youtube Video by 'TRXbench' about MiniVNA-Tiny

Very instructive Video about the MiniVNA-Tiny in english.

A customer writes: (product was not bought at WiMo):

On 11/12/2014 10:53 PM, KK4ICE/Dan Gunter wrote: The MiniVNA Tiny arrived this afternoon. Installation of drivers and software was a breeze, only taking about ten minutes to complete. And the Tiny is one incredible device! Although the VNA/J software is loaded with tons of features, getting it up and running with the Tiny is a piece of cake and I was graphing and adjusting antennas within about 20 minutes of opening the package and starting the installation steps. I was crazy about this thing within minutes of firing it up, but the more I discover that the VNA/J software paired with the Tiny will do, the better it gets. Even measuring and testing coaxial cables just became easier than ever before. In short: I'm wild about this small but extremely powerful little device. It's sure to secure and keep its place as my main device for tuning antennas, rendering all other antenna tuning devices I've owned virtually obsolete. For serious antenna builders, I can't recommend the MiniVNA Tiny enough. On a scale of 1 to 10, so far I'm giving in about a 15. :-) KK4ICE / Dan

Mini-VNA PRO BT Antenna analyser with Bluetooth

Il Mini-VNA Pro BT è uno sviluppo ulteriore del famoso analizzatore di reti mini-VNA, acclamato in tutto il mondo. I miglioramenti più evidenti sono la batteria agli ioni di litio entrocontenuta e la nuova interfaccia bluetooth. Entrambe le modifiche vi permettono di usare il mini-VNA Pro BT all'aperto, direttamente alla base dell'antenna.

Ulteriori funzioni e dettagli tecnici del Mini-VNA Pro BT

  • Campo di frequenza da 0.1 a 200 MHz
  • Calibrazione su carico aperto o chiuso per ottenere elevata precisione
  • Campo di impedenze Z da 1 a 1000
  • Due porte VNA con visualizzazione S11 e S12; dati visualizzati e salvati
  • Generatore DDS I/Q con potenza di uscita da 0 dBm
  • Gamme di Frequenza 0.1 a 200MHz
  • Due uscite RF per prove I/Q, SDR e misure IMD con attenuatori indipendenti da 0 a 55 dB, angolo di fase regolabile con passi da 1°
  • Adattatore Bluetooth entrocontenuto (Classe 1) per misure radio in remoto
  • Batteria agli ioni di litio da 1000 mAh entrocontenuta (fino a 4 ore di operazioni)
  • Caricabatteria entrocontenuto (fino a 400 mA)
  • Connessione per futuri accessori opzionali, interfacce ed estensori di frequenza
  • Basso assorbimento, 220 mA a 3.6 Volt (modalità analizzatore utilizzando la porta USB)
  • Modalità a basso consumo
  • Connettori SMA per un migliore isolamento
  • Gamma dinamica estesa: fino a 90 dB per trasmissione, fino a 50 dB per riflessione
  • Boot loader per aggiornamenti firmware futuri
  • Interfaccia semplice e amichevole per PC Windows, Linux e MAC.
  • Carte di Smith integrate, in software
  • Misura dei parametri dei cristalli, lunghezza dei cavi e altro
  • Esporta i dati nei formati: JPG, Excel, ZPLOT, S2P, PDF
  • Volume de consegna:
  • Mini VNA Pro BT con batteria
  • Cavo USB

Note on Software: The software for both versions Mini-VNA and Mini-VNA Pro BT is continously developed. For this reasons a CD ROM is not included in shipment anymore. The current software is always downloadable from the internet. We recommend for example the program vna/J by DL2SBA. This is an application written in Java which runs fine under Windows, MacOS and Linux. This is also the software which is linked to by the manufacturer.

Ordine No.
MINIVNAPROBT mini-VNA Pro BT 389.00 € Ordina
42873 Adattatore SMA maschio/N femmina 8.30 € Ordina
42874 Adattatore SMA maschio/PL femmina 6.10 € Ordina
42854 Adattatore SMA maschio/BNC femmina 6.80 € Ordina
21005.03 Attenuator 3 dB, 1 Watt, SMA 24.50 € Ordina
21005.06 Attenuator 6 dB, 1 Watt, SMA 24.50 € Ordina
21005.10 Attenuator 10 dB, 1 Watt, SMA 24.50 € Ordina
21005.20 Attenuator 20 dB, 1 Watt, SMA 24.50 € Ordina
Info sui costi di spedizione
Download: Software for Android Smartphone/Tablet (Google Play Store)
Download: MiniVNA Pro BT Hardware Guide (PDF, EN, 910KB)

miniVNA-Pro - wireless measurement via Bluetooth
miniVNA-Pro

A customer writes:
    ------ Original Message --------
    On 6/20/2012 4:12 PM, Michael Golovnya wrote:
    Dear Ralph,

    I have it!!!  It works! Unbelievably cool piece of equipment,
    way better than my old ***.  Feels like I finally got an inside
    passage into my antennas and transmission lines.

    73s
    Mike

    ------ Original Message --------
    Subject:     RE:
    Date:     Thu, 21 Jun 2012 16:44:18 -0700
    From:     Michael
    To:     Ralph


    Ralph,

    Sure, you can quote me! Today I started playing with the bluetooth mode,
    unbelievably convenient.  Another thing I discovered is that you can run
    the analyzer continuously and see how tuning network controls (like antenna
    tuner, etc.) impact your SWR, etc. in real time!  This is a great tool to
    gain solid understanding of all important RF concepts, I only wish I had it
    available years ago when I was first learning about radio.

    73s

    Mikhail
    KJ6LKO
    

Calibration Kit SMA

21010.SMA

For calibration of the Pro-miniVNA BT, we recommend this calibration set, consist of one 50Ω terminator, ref. 21001.SMA plus one open, one short.

Ordine No.
21010.SMA Calibration Kit SMA 21.00 € Ordina
Info sui costi di spedizione