Magnet with M6 screw. Very useful for installation of small and lightweight antennas, wires and other items temporarily. Diameter of magnet approx. 55mm, with rubber cap.
For all kinds of masts, tubes... up to 60mm diameter. Includes reduction rings for smaller diameters and a lever to screw the spit into ground. Length 54cm, weight 1.5kg
Please note that when using this spit that the forces at the lower end of the tube or mast can be very high. This can damage the tubing. We recommend to install the mast completely without the spit, and then later set it into the spit when the guy wires are complete.
Make any kind of clamps with Clamptite. These wire clamps replace the usual worm drive steel clamps found on hoses etc. (and of which you usually have the required size not at hand...). Works with nearly any wire, we recommend stainless steel wire, but you can also use welding wire, copper wire or even a wire coat hanger! The wire is slung around the piece to fix, tightened with the Clamptite tool and finally cut off. The ends of the wire are bent backwwards, so you don't have any extruding parts as with traditional clamps.
Build hose clamps of any size, repair the fence post or the hammer grip or connect a broken rope. There are no limits to the use of this handy tool. It belongs in any tool box, whether you are a sailor, a radio amateur, farmer ...
It's use is significantly cheaper that traditional steel clamps. On coil of steel wire usually lasts for 100 clamps, compare that to 100 stainless steel worm drive clamps. And the clamps are easy to loosen as well - just cut the wire.
The Clamptite tool is available in various sizes. The standard tool can be used with wire up to 2mm diameter (depending on strength of the wire), the largest model can be used with wire up to 6mm diameter.
The large suction cup holder has a diameter of 120mm, is very solid and is ableto carry also larger portable antennas, enabling HF operations from the hotel. Or use it to carry our WiFi antenna to connect to the next hotspot, just by mounting your WiFi antenna outside on the window.
The suction cup holder comes complete with a versatile mounting bracket which is suitable for mounting mobile antenna bases, coaxial sockets ot a magnet base antenna. An extension kit is available as an option. This option kit contains a second bracket, hardware and two U bolts for installing a tube of up to 20mm diameter.
With the suction cup holder many kinds of antennas can be easily installed securely and very fast. Whether you are on a conference, a public event, in vacation, with your car - there are possibilities without end.
Guy clamp
Smart construction which finally avoids that the guy wires and antenna cables get entangled. That happens most often at the topmost guying.
Solid metal disc, the gap for the cable guide is wide enough (25mm) to accomodate most rotor connectors. The same product can be used to guy a mast in several heights: included in the shipment are bushings for 50, 40, 30 and 20mm mast diameter. Of course the mast can still be rotated ín the guy clamp.
|
Double clamp

Double clamp 32/42mm, galvanised
|
Element holder for VHF/UHF antennas
|
Guying clamp
|
Mast base clamp max. 50 mm
|
Mast clamp
|
Guy wire tightener
| Order No. |
|
|
|
|
|
| 23011 |
6mm, galvanised |
2.90 € |
Buy now |
| 23012 |
8mm, galvanised |
3.60 € |
Buy now |
| 23013 |
10mm, galvanised |
5.60 € |
Buy now |
|
Guy wire thimble
| Order No. |
|
|
|
|
|
| 23020.03 |
3mm, galvanised |
0.50 € |
Buy now |
| 23020.04 |
4mm, galvanised |
0.50 € |
Buy now |
| 23020.06 |
6mm, galvanised |
0.80 € |
Buy now |
| 23020.08 |
8mm, galvanised |
0.80 € |
Buy now |
|
Guy wire clamps
For security reasons we recoomend the use of two clamps one each end.
| Order No. |
|
|
|
|
|
| 23025.03 |
3mm, galvanised |
0.50 € |
Buy now |
| 23025.06 |
6mm, galvanised |
0.50 € |
Buy now |
| 23025.08 |
8mm, galvanised |
0.80 € |
Buy now |
|
U bolts

including nuts and lockwashers, stainless steel
| Order No. |
|
|
|
|
|
| 23040.40 |
40mm Width, M8 |
3.90 € |
Buy now |
| 23040.50 |
50mm Width, M8 |
4.30 € |
Buy now |
| 23040.60 |
60mm Width, M8 |
4.90 € |
Buy now |
| 23040.65 |
65mm Width, M8 |
5.00 € |
Buy now |
| 23041.20 |
20mm Width, M6 |
4.00 € |
Buy now |
| 23041.50 |
50mm Width, M6 |
4.00 € |
Buy now |
| 23041.54 |
54mm Width, M6 |
4.00 € |
Buy now |
| 23041.42Z |
42mm Width, M6, 2 pcs., Zinc plated! With nuts but without washers, 2 pcs. |
1.50 € |
Buy now |
|
Mounting plates, stainless steel
| Order No. |
|
|
|
|
|
| 23052 |
(40 x 40mm, V2A) |
11.80 € |
Buy now |
| 23051 |
(50 x 50mm, V2A) |
15.40 € |
Buy now |
| 23053 |
(50 x 60mm, V2A) |
18.50 € |
Buy now |
|
Tube clamps
For tubes, for example for DIY mounting plates, galvanized or stainless steel
| Order No. |
|
|
|
|
|
| 23035.28 |
Stainless Steel 28mm |
3.90 € |
Buy now |
| 23035.32 |
Stainless Steel 32mm |
3.70 € |
Buy now |
| 23035.42 |
Stainless Steel 42mm |
3.90 € |
Buy now |
| 23035.50 |
Stainless Steel 50mm |
4.00 € |
Buy now |
| 23035.60 |
Stainless Steel 60mm |
4.10 € |
Buy now |
| 23035.65 |
Stainless Steel 65mm |
4.30 € |
Buy now |
| 23036.28 |
Steel galvanized, 28mm |
0.80 € |
Buy now |
| 23036.32 |
Steel galvanized, 32mm |
0.95 € |
Buy now |
| 23036.42 |
Steel galvanized, 42mm |
1.50 € |
Buy now |
| 23036.60 |
Steel galvanized, 60mm |
1.90 € |
Buy now |
| 23036.65 |
Steel galvanized, 65mm |
1.90 € |
Buy now |
|
Cross Clamp
Massive cross clamp, for vertical diameter from 35 to 70m, horizontal diamteer up to 45mm. Nuts and bolts stainless steel.
|
Half shell 40mm
Material Aluminium, thickness 1mm.
| Order No. |
|
|
|
|
|
| 23095 |
short, 120mm for antenna |
6.20 € |
Buy now |
| 23096 |
long 240mm for Rotor |
9.20 € |
Buy now |
|
Clamp sleeve für glass fibre tubes

Thick walled clamp sleeve 50x5mm for glass fibre tubes with 40mm diameter, to be used together with mounting plates 23055, length 125mm
|
Wall holder
| Order No. |
|
|
|
|
|
| 23075 |
Extension 250mm |
27.00 € |
Buy now |
| 23076 |
Extension 460mm |
30.70 € |
Buy now |
|
Antenna mast clamp, complete
| Order No. |
|
|
|
|
|
| 23003 |
for 15x15mm boom tubes |
11.30 € |
Buy now |
| 23004 |
for 20x20mm boom tubes |
11.30 € |
Buy now |
|
Guy wire clamp

for Nylon rope, rope diameter 3.5-8mm
|
S hook for rope tightener
|
Mounting plates complete with 4 U brackets and nuts

All items stainless steel
Order No.
23044 40x40mm 29.50
EUR
Buy now
23055 50x50mm 29.80
EUR
Buy now
23056 50x60mm 39.00
EUR
Buy now
|
Wall holder for masts

For masts with diameter from 30 to 50mm, distance from wall 220mm. Hot dipped galvanised steel, with additional support. Two of these holders are required for one mast.
The max. mast diameter is determined by the length of the supplied screws. With longer screws up to 60mm mast diameter would be possible.
|
Pipe clamp
Pipe clamps for portable masts etc.
| Order No. |
|
|
|
|
|
| 23045.20 |
20mm Ø, galvanised |
3.80 € |
Buy now |
| 23045.25 |
25mm Ø, galvanised |
4.10 € |
Buy now |
| 23045.30 |
30mm Ø, galvanised |
4.40 € |
Buy now |
| 23045.35 |
35mm Ø, galvanised |
4.70 € |
Buy now |
| 23045.40 |
40mm Ø, galvanised |
5.10 € |
Buy now |
| 23045.45 |
45mm Ø, galvanised |
5.40 € |
Buy now |
| 23045.50 |
50mm Ø, galvanised |
5.70 € |
Buy now |
| 23045.55 |
55mm Ø, galvanised |
6.00 € |
Buy now |
| 23045.60 |
60mm Ø, galvanised |
6.30 € |
Buy now |
| 23045.65 |
65mm Ø, galvanised |
6.60 € |
Buy now |
| 23045.70 |
70mm Ø, galvanised |
6.90 € |
Buy now |
|
V2A Clamp
V2A stainless steel clamp for easy mounting of two parallel tubes, incl. screws.
|
Latch

Stainless Steel 90x27x22mm, suitable for 6mm screws. This latch is included with our standard mast clamps #23003 and #23004.
Order No.
23017 3.20
EUR
Buy now
|
Wire clamps
Wire clamp 3mm, stainless steel
|
Double clamp

Used to mount or extend two tubes in parallel. Diameter from 25 to 50mm. Made from steel 3mm thick, galvanised. Weight 0,9kg.
|
Large double clamp
Used to mount or extend two tubes in parallel, with additional distance (140mm) between tubes. Diameter from 25 to 50mm. Made from steel 3mm thick, galvanised. Weight 1,2kg.
|
Versatile antenna mount
 Tilt/
Swivel mount for antennas etc., for masts with max. diameter 50mm. Also suitable for wall mount, just leave out the two U brackets. Aluminium die cast parts, U bolts and nuts stainless steel.
|
|
Mast cap 32 to 48mm
|
Guy wire kit
For guying of masts or antennas. Kit consists of one guying clamp (30-50mm diameter) and 30 or 60m black 3mm DACRON rope (polyester) with a breaking load of 120kg.
|
Tube cap, various sizes
Caps for masts or tubes, material PVC. Size is given for the outer diameter of the tubes, suitable for tubes with wall thickness up to 2.5mm.
|
Cable Ties
Various cable ties for antenna installations or the shack. Black, UV resistant.
| Order No. |
|
|
|
|
|
| 23140.025 |
25 pcs, 100 x 2.5mm |
1.95 € |
Buy now |
| 23140.100 |
100 pcs, 100 x 2.5mm |
3.95 € |
Buy now |
| 23141.025 |
25 pcs, 200 x 2.5mm |
2.35 € |
Buy now |
| 23141.100 |
100 pcs, 200 x 2.5mm |
4.75 € |
Buy now |
| 23142.025 |
25 pcs, 295 x 4.8mm |
3.90 € |
Buy now |
| 23142.100 |
100 pcs, 295 x 4.8mm |
7.80 € |
Buy now |
| 23143.025 |
25 pcs, 430 x 4.8mm |
7.90 € |
Buy now |
| 23143.100 |
100 pcs, 430 x 4.8mm |
19.90 € |
Buy now |
| 23144.025 |
25 pcs, 365 x 7.8mm |
14.90 € |
Buy now |
| 23144.100 |
100 pcs, 365 x 7.8mm |
29.90 € |
Buy now |
| 23145.010 |
10 pcs, 540 x 7.8mm |
15.90 € |
Buy now |
| 23145.025 |
25 pcs, 540 x 7.8mm |
24.90 € |
Buy now |
| 23146.010 |
10 pcs, 500 x 12.5mm |
15.90 € |
Buy now |
| 23146.025 |
25 pcs, 500 x 12.5mm |
24.90 € |
Buy now |
|
Lead roof brick

Adjustable to any form, for masts with up to 48mm diameter.
|
|
Self welding sealing tape

For sealing of antenna connections, coax connectors etc. Elastic tape, self welding and UV resistant. Width 60mm, available in 1m lengths. Also suitable for lead roof brick 23058.
|
Mast arm incl. clamp
| Order No. |
|
|
|
|
|
| 23070 |
one sided, 500mm extension, 35mm diameter |
29.00 € |
Buy now |
| 23071 |
double sided, 2x 500mm extension, 35mm diameter |
38.00 € |
Buy now |
|
Dyneema guy rope

Dyneema rope, only 3mm thick and very unobtrusive. High breaking load of 400 Kg! Pre-stretched, only minimal strechting when wet.
| Order No. |
|
|
|
|
|
| 23100 |
Dyneema, price per meter |
1.00 € |
Buy now |
|
PES guy rope

Braided PES guy rope, 5mm with 420kg breaking load. Low strecht, weather proof, UV resistant.
| Order No. |
|
|
|
|
|
| 23102 |
per meter |
0.50 € |
Buy now |
| 23102.100 |
100m coil |
46.20 € |
Buy now |
| 23102.200 |
200m coil |
86.20 € |
Buy now |
|
Nylon Monofil guy wire

Nylon Monofil is a new type of guy wire for antennas and masts. Monofil is not braided buit one solid wire of nylon, extremely solid, extremely low stretch, breaking load of the 5mm wire is 700kg! But still lightweight and weatherproof and due to the white color quite unobtrusive. For even higher breaking loads use several wires in parallel. Can be fitted with the usual mounting hardware.
The 2mm version can be used to brace antennas etc.
Technical Data 5mm Monofil (23101.x):
- Material: 6 SNIA Nylon
- Specific weight: 1.14 g/cm3
- Specific breaking load: 35-40 kg/mm2
- Breaking stretch: 15-20%
- Diameter: 2 mm or 5 mm
- Breaking load: 120 kg (2mmØ), 700 kg (5mmØ)
| Order No. |
|
|
|
|
|
| 23101.5 |
5mm, per meter |
0.90 € |
Buy now |
| 23101.5-50 |
5mm, 50m coil |
43.50 € |
Buy now |
| 23101.5-100 |
5mm, 100m coil |
83.50 € |
Buy now |
| 23101.2-25 |
2mm, 25m coil |
15.00 € |
Buy now |
| 23101.2-50 |
2mm, 50m coil |
30.00 € |
Buy now |
| 23101.2-100 |
2mm, 100m coil |
60.00 € |
Buy now |
|
Light guy rope
Light rope, suitable for guying lines of masts and verticals. Nearly invisible, UV resistant white polyester, 16 times braided, low stretch, breaking load 150kg, available as 30 or 60m coil.
| Order No. |
|
|
|
|
|
| 23105.30 |
30m coil |
9.00 € |
Buy now |
| 23105.60 |
60m coil |
16.00 € |
Buy now |
|
Tilting base

Universal antenna base, for concrete or similiar foundation. Allows fast and easy tilting of ground mounted vertical antennas. Suitable for tube diameters of 30 to 50mm. Also useable for fielddays when the base is installed temporary.
|
Weather Guard TM

Clear varnish for any antenna, protects against salt, acid rain and UV light. Just apply to the outside of any completely assembled antenna. Keeps your antenna 'like new' for many years.
Can with 8 fl. oz, approx. 0.23 Liter.
|
Butter-its-not

Conductive lubricant, to applied to the telescopic tube ends of antennas. Provides excellent electrical connection without electrolysis, prevents seizing of tubes. Packet includes 30gr.
|
Stainless steel guy wire

Steel guy wire, 6mm diameter, braided 6x7 wires, 13mm2 cross section. Statical breaking load approx. 21kN (approx. 2 tons).
|
Epoxyd Two-component adhesive
Fast hardening, transparent glue, results in extremely strong connection. Glue cures to a elastic connection where high attraction resilience to impact forces are required. Can be used with metal, glas, stone, ceramics, wood and most hard plastics. 24ml, in convenient dual-syringe, recloseable.
|
Lightweight Wand holder

Lightweight wand holder for small antennas like 70cm GPs or Wifi antennas. Tube diameter 30mm, distance to wall c. 17cm, welded aluminium.
|
Epoxyd 5 minute repair glue
Fast hardening glue, two components for repairs or small quantities. Hardens within 3 to 5 minutes, pouch with 4g.
|
Tuning rod

4mm tube, solderable, length 100 mm, with clamp and stainless steel rod.
|