Rotator Accessories

ARS-USB Rotator Interface with USB

RCI-EL USB Interface

Rotator interface with USB, in enclosure. Universally useable with practically any rotator and any software.

To the page with ARS-USB Rotator Interface

Other Rotor Accessories

Thrust Bearing GS-050

50 mm thrust bearing for mast diameters up to 50 mm, ball bearing design, with 4 installation bolts. The bearing can be used without a mast platform with guys (see drawing); the required support ring to attach the guys are supplied with the GS-050. Small protective metal pieces prevent any damage to the mast when fixing the installation nuts. Mechanical installation as with the model GS-680U, however, mast diameter only 66 mm. Does not fit the rotator platforms!

Order No.
25020 Thrust Bearing GS-050 45.40 € Buy now
Info freight charges

Thrust bearing GS-065

Thrust bearing for mast diameters up to 65 mm, 8 nuts, double ball bearing design. All other data see model GS-050. Diameter of the hole in the mounting platform is 85 mm (see drawing).

Order No.
25021 Thrust Bearing GS-065 74.80 € Buy now
Info freight charges

Thrust bearing GS-680U

Heavy duty thrust bearing with tilt compensation up to 5 degrees. Mast diameter 35-68 mm, weight approx. 1.4 Kg. The mast pipe is fixed by means of two mast clamps. Installation holes same as with GS-65. The bearing can be disassembled, so it can be mounted on an existing mast without removing the antennas.

Order No.
25022 Thrust Bearing GS-680U 113.90 € Buy now
Info freight charges

Set of stainless steel screws

Replacement of the galvanized nuts and bolts provided for the rotators and mast clamps. This is actually a good idea and almost guarantees problem-free disassembly of the antenna system even after years of use. Comes complete with nuts, bolts and washers.

Order No.
25027 Set of stainless steel screws 8.20 € Buy now
Info freight charges

Rotor platform GPF-60

Heavy-duty platform for rotators and thrust bearing up to 60 mm rotating mast diameter, fixed mast diameter 50-70mm. Hot-dipped galvanized. Distance from center of mast to end of platform: approx. 275mm. Distance from center of mast to center of mounting position (center of rotor/bearing): approx. 195mm. The thrust bearing GS-050 (Order No. 25020) can not be mounted on this platform!

Order No.
25031 GPF-60 49.20 € Buy now
Info freight charges

Set of clamps

GC-038/GC-048
Set of clamps for YAESU rotators. These clamps are required in case the rotator is installed on top of a mast instead on a platform. Supplied complete with a set of galvanized nuts & bolts.

Order No.
25025 GC-038 (G-450, 650, 800, 1000) 36.20 € Buy now
25026 GC-048 (G-2800) 56.90 € Buy now
Info freight charges

Absorber joint

Tower Absorber Joint for KENPRO/YAESU Rotators
Absorber joints for KENPRO/YAESU rotators; installed in-between rotator and installation platform. Allows compensation of up to 2 degrees tilt. Reduces strain and torque of the rotator and avoids sudden block of the rotation. The integrated shock absorber further reduce vertical torque caused by wind gusts as well as mechanical shock and vibrations originating from starting and stopping the rotator.

GA-2500 has a 2-way bearing and is recommended for G-450 / G-650
GA-3000 has a 4-way bearing and is recommended for larger rotors like G-1000/G-2800DXC.

Order No.
25035 GA-2500 (G-450, 650, 800) 70.30 € Buy now
25036 GA-3000 (G-1000, G-2800SDX) 114.50 € Buy now
Info freight charges

Connectors for Yaesu rotor

Connectors for Yaesu rotors

Yaesu 40M-WP set of connectors for current Yaesu rotators. One 6 pin square connectors for the control unit, one 7 pin round connector with rubber cap for rotators. Solder connectors, suitable cable is #40010 (see below).

Order No.
25029 Connectors Yaesu 35.40 € Buy now
Info freight charges

Rotor control cable, 25m/50m

Rotorsteuerkabel

25m/50m rotor control cable, suitable for Yaesu rotors, equipped with connectors.

Order No.
25028 25m Rotor control cable 81.80 € Buy now
Info freight charges

Custom Rotor Control Cable

Rotorsteuerkabel

Custom Yaesu rotor control cable, available in lengths from 1 to 500m, just enter the required length.

Control Cable, per meter

PVC control cable, 5, 6 or 8 wires, 0.75 mm², suited for all YAESU rotators (6 wires). Use two separate cables (12 wires) for satellite rotators. Color code wires.

Order No.
40010.5 5 wires, 0.75mm²,per m 1.10 € Buy now
40010.6 6 wires, 0.75mm²,per m 1.30 € Buy now
40010.8 8 wires, 0.75mm²,per m 1.70 € Buy now
Info freight charges
Order No.
ZG40010.08.1 Rotor-Steuerkabel 8 Länge/ length 21m 32.00 € Buy now
ZG40010.08.5 Rotor-Steuerkabel 8 Länge/ length 8m 12.20 € Buy now
Info freight charges