WLAN Antennas 2.4GHz
Directional antennas for outdoor use

Antennas with directional capabilities suitable for outdoor use.
Usage: To cover longer sictances from building to building. Usually directional antennas are used on both sides of the link. In some cases it might be sufficient to use a directional on one side only and use the original euqipment antenna on the other side.

Flat panel antennas

PA-13R		PA-13R-20
Flat panel antennas consist of one or more radiators placed in front of a reflecting backside. With this principle short, robust and unobtrusive antennas can be designed, which have a high gain and a high bandwidth. Our flat panel antennas are made from weatherproof aluminum, all other hardware is stainless steel. The antennas can be mounted with either horizontal or vertical polarization, all mounting hardware for mast mount is included. The radome protects the antenna system against adverse weather like rain, hail or snow.

Type	PA-13R	PA13R-18	PA-13R-20
Frequency	2320-2500	2320-2500	2320-2500	MHz
Gain	11	18	20	dBi
HPBW V:	54	20.7	13	°
HPBW H:	67	25.8	15	°
Front/Back ratio	>20	>20	>20	dB
SWR	<1,5	<1,5	<1,5
Max.Power load	100	50	50	Watt
Weight ca.	1,3	1,5	1,7	Kg
Sizes	130x130	290x300	330x330	mm
Windload at 160 km/h	130	150	180	N
Connector	N jack (female)	N jack (female)	N jack (female)
Order No.	18033 74.98 (72.80) EUR	18033.18 115.15 (111.80) EUR	18033.20 142.66 (138.50) EUR
Tilt mount	n/a	Included	18033.20NH 11.64 (11.30) EUR

PA-13R-18 with included pan/tilt mount

PA-13R20 with optional tiltmount)

Suitable cables for PA-13Rxx antennas

Antenna cable Reverse-SMA plug to N plug, H-155 Cable suitable for all devices (Router, AP, PCI cards etc.) with Reverse-SMA connector. Order No. 40330.1 100cm20.91 (20.30) EUR 40330.2 200cm21.84 (21.20) EUR 40330.3 300cm22.87 (22.20) EUR 40330.4 400cm23.79 (23.10) EUR 40330.5 500cm24.72 (24.00) EUR 40330.6 600cm25.65 (24.90) EUR 40330.7 700cm26.68 (25.90) EUR 40330.8 800cm27.60 (26.80) EUR

Antenna cable Reverse-TNC plug to N plug, H-155 Cable suitable for all devices (Router, AP, PCI cards etc.) with Reverse-TNC connector. Order No. 40334.1 100cm18.95 (18.40) EUR 40334.2 200cm19.88 (19.30) EUR 40334.3 300cm20.81 (20.20) EUR 40334.4 400cm21.73 (21.10) EUR 40334.5 500cm22.76 (22.10) EUR 40334.6 600cm23.69 (23.00) EUR 40334.7 700cm24.62 (23.90) EUR 40334.8 800cm25.54 (24.80) EUR Other length on request.

Housing for AP with one or two 2.4G antennas

The PRG-2400 is a flat panel wireless LAN antenna (2.4GHz) with an empty housing. This box is ideally suited for intergation of an accesspoint our WiFi router. Due to the short cable length to the antenna the attenuation is minimal. The external connection is done with an RJ45 ethernet cable, the feed through is protected against water, as well as the box itself of course. So the electronics are always perfectly protected.
The housing PRG-2400 is an ideal solution for the setup of WiFi hotspots or point-to-point links, where the required cable length to an external antenna is too long. The inner size of the box is sufficient to install mostly any AP or router, the PCB is mounted to the solid metal backplane. The power supply is done with power-over-ethernet (POE). The antenna comes with a 12cm cable with RP-TNC or RP-SMA connector, other connectors available on request.

PRG-2400-12: Stainless mounting hardware is included for mast or wall mounting, the mounting allows pan and tilt.
PRG-2400-18: Stainless mounting hardware is included for mast mounting, the mounting allows pan and tilt. For wall mounts a separate wall holder needs to be ordered.

• Flat panel antenan with 12dBi gain
• 12cm cable with RP-TNC or RP-SMA connector internally (others available on request)
• Weatherproof ABS housing
• Housing and cable feed through splash-proof
• Mounting bracket also suitable for wall mounting

Cable feed through internally, 2x RJ45 jack

Inner view, rear of antenna with cable

PRG-2400 Dual

As a variant this housing is also available with an additional N jack on top. Here an omni directional antenna can be installed, proving all antennas for a very compact hotspot solution. The directional panel antenna provides the connection to the backbone, the omni supplies the local clients.
Suitable omni antennas by WiMo are VC-2400 or MG-200.

Instead of an omni antenna a directional antenna could be connected to the N jack, allowing for a compact repeater system for longer distances.

PRG-2400 "Dual" with N jack for omni antenna

Model	Gain [dBi]	2nd Antenna	Inner size [mm]	Outer size [mm]	Max. Mast diameter [mm]	Weight [kg]	Connector	Order No.	Price
PRG-2400-12	12dBi	No	170x170x30	195x195x75	45	0,97	1x RP-TNC	18795	103.52 (100.50)EUR
							1x RP-SMA	18795.RSMA	114.12 (110.80)EUR
PRG-2400-12 Dual	12	Yes	170x170x30	195x195x75	45	0,97	2x RP-TNC	18795.D	EUR
							2x RP-SMA	18795.DRSMA	115.15 (111.80)EUR
PRG-2400-18	18	No	310x340x34	370x345x65	52	2.7	1x RP-TNC	18797	167.89 (163.00)EUR
							1x RP-SMA	18797	178.60 (173.40)EUR
PRG-2400-18 Dual	18	Yes	310x340x34	370x345x65	52	2.7	2x RP-TNC	18797.D	EUR
							2x RP-SMA	18797.DRSMA	174.38 (169.30)EUR

WLAN Outdoor antenna with router box

Bridgepoynt (18790)

The "Bridgepoynt" is a flat panel wireless LAN antenna (2.4 or 5 GHz) with a weatherproof empty housing. This box is ideally suited for intergation of an accesspoint our WiFi router. Due to the short cable length to the antenna the attenuation is minimal. The external connection is done with an RJ45 ethernet cable, the feed through is protected against water, as well as the box itself of course (class IP65). So the electronics are always perfectly protected.
The Bridgepoynt housing 2400 is an ideal solution for the setup of WiFi hotspots or point-to-point links, where the required cable length to an external antenna is too long. The inner size of the box is sufficient to install mostly any AP or router, the PCB is mounted to the solid metal backplane. The power supply is done with power-over-ethernet (POE).

18790 Mounting bracket

Techn. Data:

	2.4GHz	5GHz
Gain	17 dBi	23 dBi
Frequency range	2.4 - 2.5 GHz	5 - 6GHz
HPBW hor.	19°	11°
HPBW vert.	32°	16°
Polarisation	Linear
Max. Power	10W
Internal antenna connector	SMA Buchse
Max. Wind speed	160 km/h
Case	ABS
Protection class	IP 65
Outer size	364 x 258 x 98 mm
Internal space for installations	200 x 300 x 40 mm
Order Nr.	18790.24	18790.5
Price	101.97 (99.00)	122.57 (119.00)

Wifi Outdoor antenna with router box 15/18dBi 'iPoynt'

iPoynt (18792.xx)

A little bit smaller and unobtrusive, with somewhat less gain than it's larger brother (see above). But sufficient for most CPE applications - still 15dBi gain on 2.4GHz and 18dBi on 5GHz.
The new 'iPoynt' antennas have a weatherproof RJ-45 connector, no need to open the case for connecting the cable. Includes a universal swivel and tilt mount for mast or wall mounting. The bottom side of the antenna offers space for installation of additional N-sockets for more external antennas (needs holes to be drilled).

Techn. Data:

	2.4GHz	5GHz
Gain	15 dBi	18 dBi
Frequencyrange	2.3 - 2.7 GHz	5.1 - 5.9 GHz
HPBW hor.	30°	15°
HPBW vert.	30°	15°
Polarisation	Linear (H or V)
Max. Power Load	10 W
Internal Antenna Connector	SMA female
Max. Wind speed	160 km/h
Material	ABS
Protection Class	IP 65
max. Mast diameter	max. 60mm
Outer size	235 x 210 x 55 mm
Inner size	200 x 190 x 23 mm
Weight	1 kg
Order No.	18792.24	18792.5
Price	81.37 (79.00)	81.37 (79.00)

Swivel and tilt mount

18792.xx iPoynt Internally

Helix antennas

Helix antennas are directional antennas for circular polarization mainly developed for satellite communications but just as well usable for terrestrial operations. Due to physics based reasons the circular polarization shows significant advantages when the received signal may consist of a mix of all kinds of polarizations due to heavy reflections. As an example: If the phase of a received signal is perpendicular to the antenna plane the resulting signal level can be up to 18 dB down compared to a normal yagi! The right-hand circular polarization originates from a helix - the antenna radiates into the direction of the helix. The reflector directs the electromagnetic energy forward; to decrease the antenna's wind load the reflector is perforated (many small holes). All antennas shown here are designed for fore-mast installation. By means of power splitters the helix antennas can be combined to form antenna groups of 2 or 4. The antennas have a standard N-connector and are made of non- corrosive aluminum material with all nuts and bolts made of stainless steel.

	Helix 13	Helix 13-40
Frequency range	2300-2450	2300-2450	MHz
Gain (righthand circular)	14	16	dB
Turns	21	40
SWR	1,5	1,5
Max. power load	500	500	Watt
Connector	N jack	N jack
Max. mast diameter	60	60	mm
Length	0,8	1,25	m
Screen diameter	10	10	cm
Weight	0,7	1,1	Kg
Windload	70	110	N
Order No.	18028 103.52 (100.50) EUR	18029 125.66 (122.00) EUR

Suitable cables for Helix antennas

Wifi solid Grid Dish 2.4

18685.x

The Wifi grid dishes are made from casted aluminium and combine a high stability and low wind load for a long endurance of the antennas. The carefully designed parabolic dish offer a gain of 26dBi on 2.4GHz and 31dBi on 5GHz. In contrast to other parabolic dishes these antennas are designed for best performance also on 5GHz.
Due to the split construction of the reflector (90x70cm) the shipping size is very small, very facorable for the shipping ost. A tilt/swivel mount for mast mounting is included. Connector N female.

Technical data

Frequency range	2.4-2.8	5.1-5.85	GHz
Gain	26-27	31	dBi
HPBW	8/11°	12°
Wind speed	160	160	km/h max.
Price	113.30 (110.00) EUR	132.87 (129.00) EUR

WLAN Prime Focus Parabolic dishes

Proferssional prime focus dished with 45 or 60cm diameter (18 or 21dBi gain). Solid and weatherproof finish. All required mounting hardware (stainless steel) included, connector N female. In contrast to the dish mentioned above these dishes have a linear polarization. This is beneficial in situations where tightly spaced links have to be separated by polarization, attentuation between links can be up to 25dB with different polarization. The radiators can be mounted in 45° steps in respect to the polarization angle.

Order No.
18660.24 45cm dish, 18dBi 153.99 (149.50) EUR
18662.24 60cm dish, 21dBi 184.89 (179.50) EUR

Suitable cables for Prime Focus dish antennas

Tiltmount for SP45 and SP60 prime focus dishes

Tiltmount to mount the prime focus dishes SP45/xx and SP60/xx to a mast, allows tilt ±45°. Replaces the original bracket. Very solid aluminum construction.

Order No.
18663 Tiltmount SP 33.48 (32.50) EUR

Professional Yagi directional antennas, inkl. swivel/tilt mount, suitable for wall or mast mounting. Completely enclosed, makes these antennas insensible against weather. Connector: cable pigtail with N female jack.

Typ	YA-2400-8	YA-2400-12	YA-2400-18
Frequency	2400-2483.5	2400-2483.5	2400-2483.5	MHz
Gain	8	12	18	dBi
Length without mount	221	446	851	mm
Diameter	76	76	76	mm
Max. mast diameter	50	50	50	mm
Weight incl. mount	940	1040	1240	g
Connector	N jack (female)	N jack (female)	N jack (female)
Order No.	18690.8 59.23 (57.50) EUR	18690.12 94.04 (91.30) EUR	18690.18 121.54 (118.00) EUR

Mounting bracket of YA-2400 Yagis

Suitable cables for Yagi antennas

PA-2408A Directional antenna, 8dBi

Very small patch antenna für 2400 MHz with 8dBi gain. Includes 20cm cable with N jack (female) and wall mount which allows pan/tilt. Suitable for for indoor use to avoid multipath reception due to reflections, unobtrusive coverage of hotspots (office, coffeeshop) indoor and outdoors (waterproof). A mast mount is available separately.

Mast mount for PA-2408A

Order No
18626 PA-2408A 40.17 (39.00) EUR
18626.H PA-2408A Mast mount 20.09 (19.50) EUR

Suitable cables for PA-2408 antenna

FA-2400 WiFi antenna 2400 MHz with suction cup holder

FA-2400

Small patch antenna with 8dBi gain and SMA connector. Comes including a versatile suction cup holder which allows you to mount the antenna on any smooth surface. For example on a window pane - ideal for travellers in a hotel, on conferences or any other temporary locations. The antenna can be rotated on it's arm, covering an angle of at least 180° if necessary, very useful for situations with difficult reception.
The SMA connection is 'in principle' protected against water, still we recommend to use some self amalgating sealing tape for more permanent installations (see WiMo article 23065).

Order No.
18622 FA-2400 50.47 (49.00) EUR

This antenna exists also in a version for UMTS and Wifi 5GHz.

Suitable cables for FA-2400 Antenna

Antenna cable Reverse-SMA to SMA connector, H-155 Cable suitable for all devices with RP-SMA connector (Router, AP, PCI cards etc.) Order No. 40326.1 100cm 15.76 (15.30) EUR 40326.2 200cm 16.69 (16.20) EUR 40326.3 300cm 17.61 (17.10) EUR 40326.4 400cm 18.64 (18.10) EUR 40326.5 500cm 19.57 (19.00) EUR 40326.6 600cm 20.50 (19.90) EUR 40326.7 700cm 21.42 (20.80) EUR 40326.8 800cm 22.45 (21.80) EUR Other lengths on request.

Antenna cable Reverse-TNC to SMA connector, H-155 Cable suitable for all devices with RP-TNC connector (Router, AP etc.) Order No. 40333.1 100cm 20.91 (20.30) EUR 40333.2 200cm 21.84 (21.20) EUR 40333.3 300cm 22.87 (22.20) EUR 40333.4 400cm 23.79 (23.10) EUR 40333.5 500cm 24.72 (24.00) EUR 40333.6 600cm 25.65 (24.90) EUR 40333.7 700cm 26.68 (25.90) EUR 40333.8 800cm 27.60 (26.80) EUR Other lengths on request.

Sector antennas 12, 14, 16.5dBi

VP270/24, 12dBi Shown with optional tilt mount	VP470/24, 14dBi	VP870/24, 16.5dBi Shown with optional tilt mount
Professional sector antennas for outdoor use. Ideal for coverage of large areas like halls, outdoor areas etc. Horizontal HPBW approx. 70°, connector N jack (female). The directional pattern of these antennas is shaped in a way that the area at the installation point below the antenna is also covered to a certain extent, resulting in a more continous coverage even for antennas mounted in an elevated position.
VP-270/24 Gain: 12dBi HPBW horizontal: 70° HPBW vertical: 27° Polarization: Vertical Size: 95x235x30mm Connector: N jack (female) Mounting hardware for wall or mast mount included Optional tilt mount available Order No. 18640 200.85 (195.00) EUR	VP-470/24 Gain: 14dBi HPBW horizontal: 70° HPBW vertical: 15° Polarization: Vertical Size: 95x470x30mm Connector: N jack (female) Mounting hardware for wall or mast mount included Optional tilt mount available Order No. 18642 263.17 (255.50) EUR	VP-870/24 Gain: 16.5dBi HPBW horizontal: 70° HPBW vertical: 8° Polarization: Vertical Size: 95x945x30mm Connector: N jack (female) Mounting hardware for wall or mast mount included Optional tilt mount available Note: To use this antenna an N angled connector is recommended (not included). Order No. 18644 386.25 (375.00) EUR
Tilt mount Tilt mount bracket for VP270, suitable for azimuth and elevantion adjustment. Stainless steel, incl. all required hardware. Order No. 18645 Tilt mount VP270 44.81 (43.50) EUR	Tilt mount Tilt mount bracket for VP470, suitable for azimuth and elevantion adjustment. Stainless steel, incl. all required hardware. Order No. 18646 Tilt mount VP470 92.19 (89.50) EUR	Tilt mount Tilt mount bracket for VP870, suitable for azimuth and elevantion adjustment. Stainless steel, incl. all required hardware. Order No. 18647 Tilt mount VP870 92.19 (89.50) EUR

Suitable cables for sector antennas

Sector antennas 11 to 17dBi

SA24-xx-xx (Front view)	SA24-xx-xx (Rear view)
Professional sector antennas 2.4GHz for indoor or outdoor use. Used for illumination of large areas like hotspots, halls, yards etc. Horizontal HPBW 90 or 120°, N female connector. The included mounting hardware allows a downtilt of up to 15° (see pictures). With several of these sector antennas (e.g. 3x 120° or 4x90°) a high performance omni directional antenna can be constructed, allowing to adjust each sector angle individualle. Ideally each of these antennas would be powered by an own AP, but it is also possible to combined several antennas with a power splitter.
SA24-90-15 Gain: 15dBi Hor. HPBW: 90° Vert. HPBW: 20° Polarisation: Vertikal Size: 625x150x64mm Weight: 1950g Order No. 18650.15 136.37 (132.40) EUR Datasheet for SA24-90-15 Sektor antenna (PDF, de/en, 100KB)	SA24-120-11 Gain: 11dBi Hor. HPBW: 120° Vert. HPBW: 25° Polarisation: Vertikal Size: 425x150x64mm Weight: 1700g Order No. 18655.11 125.66 (122.00) EUR Datasheet for SA24-120-11 Sektor antenna (PDF, de/en, 228KB)
SA24-90-17 Gain: 17dBi Hor. HPBW: 90° Vert. HPBW: 12° Polarisation: Vertikal Size: 975x150x64mm Weight: 2200g Order No.: 18650.17 157.49 (152.90) EUR Datasheet for SA24-90-17 Sektor antenna (PDF, de/en, 190KB)	SA24-120-16 Gain: 16dBi Hor. HPBW: 120° Vert. HPBW: 14° Polarisation: Vertikal Size: 975x150x64mm Weight: 2250g Order No.: 18655.16 146.88 (142.60) EUR Datasheet for SA24-120-16 Sektor antenna (PDF, de/en, 155KB)

Enclosed sector antennas 9 to 16dBi

Enclosed sector antennas 2.4-2.5 GHz for outdoor use.Used for illumination of large areas like hotspots, halls, yards etc. Horizontal HPBW 120°, N female connector. The included mounting hardware allows a downtilt of up to 15° (see pictures). With several of these sector antennas (e.g. 3x 120° or 4x90°) a high performance omni directional antenna can be constructed, allowing to adjust each sector angle individualle. Ideally each of these antennas would be powered by an own AP, but it is also possible to combined several antennas with a power splitter. Temperature range: -40... +70°.
SAK-120-9 Gain: 9dBi Hor. HPBW: 120° Vert. HPBW: 40° Polarisation: Vertikal Size: 254x120x78mm Weight: 800g Order No. 18675.9 103.52 (100.50) EUR	SAK-120-14 Gain: 14dBi Hor. HPBW: 120° Vert. HPBW: 15° Polarisation: Vertikal Size: 485x210x70mm Weight: 4500g Order No. 18675.14 177.57 (172.40) EUR
SAK-120-16 Gain: 16dBi Hor. HPBW: 120° Vert. HPBW: 7° Polarisation: Vertikal Size: 960x210x70mm Weight: 4500g Order No. 18675.16 231.44 (224.70) EUR

Suitable cables for sector antennas