Hello, if you want to change the language, you can change it here:

Hello, if you want to change the language, you can change it here:

AMA Käferlein

Käferlein Loop AMA-82 20-80m, 100W

Käferlein Loop AMA-82 20-80m, 100W

AMA Käferlein
1 430,00 €
TVA inclus, frais de port non inclus 1 201,68 €
Réforme de la TVA de l'UE à partir du 01.07.2021 : X

Dans le cadre de ce que l'on appelle le "paquet numérique", l'introduction d'un nouveau système de TVA avec des changements profonds pour le commerce transfrontalier en ligne avec les consommateurs est promue au niveau de l'UE.

À partir du 01.07.2021, dans le cadre de la vente à distance B2C (transactions avec des consommateurs finaux), les seuils de livraison TVA précédemment applicables dans l'UE seront supprimés et les montants de la taxe seront dus directement dans le pays de livraison.

Le "règlement sur la vente à distance" s'appliquera alors.

À partir de ce moment, les livraisons transfrontalières de biens à des non-entrepreneurs seront imposables dans l'État membre de destination, et le montant correspondant de la TVA y sera payable.

Cela signifie, par exemple, qu'à partir du 1.7.21, une TVA de 20% sera indiquée sur les factures pour les livraisons en France, et une TVA de 25% sera indiquée sur les factures pour les livraisons en Italie. Le destinataire en Italie ne bénéficie donc plus du taux de TVA de 19% en Allemagne.

REF: 11255.82
Uniquement sur commande, livraison vers 15 jours
AMA Magnetic Loops - Principle of construction

The main feature of a magnetic loop is it's comparably small size in relation to the wavelength. This makes this type of antenna very attractive to many radio amateurs with little space for aerials. The tuning is done with a high voltage capacitor in the loop, which is made from aluminium tubing. For best convenience the capacitor is tuned remotely by an electric motor.

Due to the physical principle of the loop antennas, these antennas have a very low radiation resistance. To achieve a good efficiency the losses in the antenna must be reduced as much as possible. This leads to the following construction requirements for AMA magnetic loop antennas:

-A magnetic loop antenna must be weatherproof for operation outside a building. The selection of materials and construction of the joints are of high importance. By many practical experiments the best suitable materials have been selected.

-The tube of the loop and the tuning capacitor must be constructed very robust, to avoid fluctuations of the inductivity and capacity and therefore fluctuations of the resonant frequency. Besides the mechanical stability the tuning capacitor must be built with thick plates, a solid axle and large electrical contacts to prevent heating from the high electrical currents. The also keeps losses at a minimum.

-For a precise tuning an accurate and continues mechanical drive, free of play, should be used. This mechanical drive must work reliably under all weather influences.

-For best radiation symmetry we will use a symmetric coupling with a secondary loop.

-The magnetic loop antenna should withstand excess power without permanent damage. This requires that the insulating material of the capacitor is resistive against high voltages, leak currents and arcing. When the antenna is accidentially overloaded there will only be a flash arc between the capacitor plates, but the antenna itself will not be damaged.

From July 2017 on, all antennas with a loop diameter larger than 1.2m are shipped with a support tube. This support tube varies in size and material (aluminium, steel) depending on the size of the antenna. It runs vertically through the antenna. The support is fixed to the antenna mount at the bottom, and to the protective cover of the capacitor at the top. It relieves the loop from strong side loads at high windspeeds.

The tube visible at smaller loops just serves to guide and protect the cable and is not designed to support the loop structurally, such an additional support is usually not required for these models.

For operation of the AMA loop antennas a DC voltage of 13.5V, max. 250mA is required, a supply cable is included in the shipment, but no power supply. Further a two wire cntrol cable is required, a wire gauge of 0.75mm² is sufficient. See below. The control cable connector is supplied. For HF a PL socket is used.

-Included in shipment of the AMA magnetic loop antennas

-Antenna

-Mast mount for vertical installation, max. 60 mm mast diameter

-Controller

-DC cable for controller

-Connector for control cable (Hirschmann STAS200 to the antenna, 3.5 mm mono phone plug to the controller)

-Printed instructions

AMA loop-antennas are partially manufactured after order. The current delivery time can be found in the listing below.
Données techniques
Efficiency 3.5 MHz 22
Mono-/Multiband multibande
Windload 280 Nm
Max. Windspeed (km/h) 120
Puissance maxi [W] 100 W
Gain 3.5 MHz [dBi] -4.7
Gain 10 MHz [dBi] 1.3
Gain 14 MHz [dBi] 1.6
Gain 7 MHz [dBi] 0.4
Polarisation Vertical
Type d'antenne Antenne omnidirectionnelle
Diamètre de flèche (boom) 1700
Conception de l'antenne Boucle magnétique
Largeur de bande (kHz) 4 - 45
Largeur de bande 14 MHz (kHz) 45
Largeur de bande 7 MHz (kHz) 26
Largeur de bande 3.5 MHz (kHz) 12
Largeur de bande 10 MHz (kHz) 4
Efficiency 14 MHz 96
Efficiency 7 MHz 72
Efficiency 10 MHz 90
Bandes supportées 20m
30m
40m
60m
80m
WiMo VOUS AVEZ ENCORE UNE QUESTION

VOUS AVEZ ENCORE UNE QUESTION?

Nous vous conseillerons volontiers!

Que vous ayez des questions sur nos produits, le processus de commande ou nos services, que vous soyez un professionnel accompli ou un débutant, peu importe! Nos experts sont à vos côtés pour vous conseiller et vous soutenir - indépendamment de la gamme de fréquences et de l'application radio.

Contactez-nous!