mAT Automatic Antenna Tuners

mAT is a supplier from China, which is specialized in the production of antenna tuners. The company is run by experienced radio amateurs and aims to develop a wide range of high quality and affordable automatic antenna tuners. Most devices can be supplied and controlled fully automatically from the radio via a control cable. WiMo started selling these tuners after extensive testing in spring 2019.

mAT-30 Tuner for Yaesu radios Nuevo

mAT-30 Tuner

The mAT-30 is an automatic tuner for the frequency range from 1.8 to 54 MHz. The tuner is compatible with a variety of Yaesu radios. Thus it can be operated on all Yaesu transceivers which can use the Yaesu tuners FC-30, FC-40 or FC-50. These are among other models: FT-100, FT-857D, FT-897D, FT-450D, FT-891, FT-950, FT-991(A). A suitable control cable for the CAT output of the radio is included. This cable is also used for the power supply.

The mAT-125E Tuner stores once found tuning settings per frequency in a memory. There are 16000 memory locations available for this purpose. If a known frequency is used again, the setting is read from the memory and the tuning process is completed in less than 0.2 seconds. If a new frequency is used or if a new frequency is to be tuned (and stored), the process takes max. 5 seconds. During the tuning process, the transmitter is offered a SWR of max. 2:1 to protect the output stage of the radio.

Operation is via the "Tune" button on the radio. This simplifies the tuning process by automatically switching to low power and CW mode, as well as switching back to the previously used transmission power and mode. The minimum tune power is 1 W, a maximum of 120 W PEP may be used, with RTTY and other continuous wave modes about 30 W max. The tuner tunes antennas in an impedance range from approx. 5 to 1500 Ohm, which is much more than the usual built-in tuners can handle.

  • Volumen de entrega
  • mAT-30 Tuner
  • Control Cable Yaesu (2x 8-pin MiniDIN
Articulo No.
MAT-30 Automatic Antenna Tuner for Yaesu Radios 214.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
40402.50CM H-155 Coaxial Cable, PL/PL, 50 cm 10.30 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
40402.01 H-155 Coaxial Cable, PL/PL, 100cm 10.90 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
Gastos de envió

mAT-125E Tuner for QRP and portable ops Nuevo

mAT-125E Tuner

The mAT-125E tuner is a compact and lightweight antenna tuner with built-in LiIon batteries. This makes it perfect for portable use, for example during a field day or SOTA activation on a hike. Due to the universal tuning, this tuner can be used with radios of all manufacturers, the only condition is that the transmission power can be reduced to 1 to 20 W. In the fully automatic mode the tuner starts tuning as soon as RF power is present, in the semi-automatic mode tuning only takes place after pressing the tune button.

The mAT-125E Tuner stores once found tuning settings per frequency in a memory. There are 16000 memory locations available for this purpose. If a known frequency is used again, the setting is read from the memory and the tuning process is completed in less than 0.2 seconds. If a new frequency is used or if a new frequency is to be tuned (and stored), the process takes max. 5 seconds. During the tuning process it can happen with the mAT-125E that the transceiver 'sees' a SWR higher than 2:1 for a short time. Some radios with extremely sensitive protection circuits already react to this and switch off the transmitter, although the tuning process could not yet be completed entirely. For these radios the manufacturer recommends a different model, for example the mAT-30 Tuner.

The operation is done via the tune button on the tuner after the transmitter has been manually switched to low power (1 to 20 W) and FM, RTTY or CW to transmit a continuous carrier. The mAT-125E can also be tuned manually in order to tune outside the transmission range (e.g. to listen to shortwave radio). In order to save power, this tuner is equipped with bi-stable latch relays, which maintain their switching state even after switching off the power supply. After 5 seconds the mAT-125E goes into a sleep state in which it only needs a few µA, the LEDs are switched off too. With a new pressing of the Tune-button the tuner wakes up again. This sleep mode can also be disabled. The front key can also be used to switch the tuner to bypass mode if the antenna does not require any tuning on a certain band. The coax output (PL) tunes antennas in an impedance range of approx. 5 to 1500 Ohm, which is much more than the usual built-in tuners can handle.

The power supply is provided by two built-in 18650 LiIon batteries with a capacity of approx. 2500 mAh. This allows for days of operation even for extended holidays. A plug-in charger is included in the scope of delivery.

Articulo No.
MAT-125E Automatic Antenna Tuner with batteries 214.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
40402.50CM H-155 Coaxial Cable, PL/PL, 50 cm 10.30 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
40402.01 H-155 Coaxial Cable, PL/PL, 100cm 10.90 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
Gastos de envió

mAT-180H Tuner for Icom/Kenwood Radios, incl. Balun Nuevo

mAT-180H

The mAT-180H is a tuner especially designed for Icom and Kenwood radios. It can be operated on all radios of these manufacturers which are equipped with the corresponding tuner socket. A tuning cable for Icom is included, a cable for Kenwood is optionally available. A special feature of this tuner is the built-in 1:4 balun. This allows the direct connection of wire antennas or a twin-lead cable. The max. permissible transmission power is 120 W PEP, for RTTY and other continuous wave modes approx. 30 W.

.

The control cable usually triggers the operation via the "Tune" or "AT" button on the transceiver. The tune process is performed automatically, including reducing the transmit power, switching to CW and back. Additionally there is the possibility to tune the tuner (L and C) manually. The mAT-180H tuner stores tuning settings for each frequency in a memory. There are 16000 memory locations available for this purpose. If a known frequency is used again, the setting is read from the memory and the tuning process is completed in less than 0.2 seconds. If a new frequency is used or if a new frequency is to be tuned (and stored), the process takes max. 5 seconds. The tuner can also be switched to a bypass mode via the front key if the antenna does not require any adjustment on a certain band. The tuning range covers an impedance range of approx. 5 to 1500 Ohm, which is much more than the usual built-in tuners can handle.

Power is supplied via the control cable from the transceiver.

  • Volumen de entrega
  • mAT-180H Tuner
  • mAT-CI Control Cable Icom
Articulo No.
MAT-180H Automatic Antenna Tuner for Icom/Kenwood with 1:4 Balun 195.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
MAT-CI Control Cable Icom (as supplied with mAT-180H and mAT-K100) 39.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
MAT-CK Control Cable Kenwood 39.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
40402.50CM H-155 Coaxial Cable, PL/PL, 50 cm 10.30 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
40402.01 H-155 Coaxial Cable, PL/PL, 100cm 10.90 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
Gastos de envió

mAT-K100 Tuner for Icom/Kenwood Radios Nuevo

mAT-K100

The mAT-K100 is a tuner designed especially for Icom and Kenwood radios. It can be operated on all radios of these manufacturers which are equipped with the corresponding tuner socket. A tuning cable for Icom is included, a cable for Kenwood is optionally available. In contrast to the mAT-180H, the mAT-K100 has no built-in balun, but only one coax output. The max. permissible transmission power is 120 W PEP, for RTTY and other continuous wave modes approx. 30 W.

.

The control cable usually triggers the operation via the "Tune" or "AT" button on the transceiver. The tune process is performed automatically, including reducing the transmit power, switching to CW and back. Additionally there is the possibility to tune the tuner (L and C) manually. The mAT-K100 tuner stores tuning settings for each frequency in a memory. There are 16000 memory locations available for this purpose. If a known frequency is used again, the setting is read from the memory and the tuning process is completed in less than 0.2 seconds. If a new frequency is used or if a new frequency is to be tuned (and stored), the process takes max. 5 seconds. The tuner can also be switched to a bypass mode via the front key if the antenna does not require any adjustment on a certain band. The tuning range covers an impedance range of approx. 5 to 1500 Ohm, which is much more than the usual built-in tuners can handle.

Power is supplied via the control cable from the transceiver.

  • Volumen de entrega
  • mAT-K100 Tuner
  • mAT-CK Control Cable Kenwood
Articulo No.
MAT-K100 Automatic Antenna Tuner for Icom/Kenwood 214.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
MAT-CI Control Cable Icom 39.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
MAT-CK Control Cable Kenwood (as supplied with mAT-K100) 39.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
40402.50CM H-155 Coaxial Cable, PL/PL, 50 cm 10.30 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
40402.01 H-155 Coaxial Cable, PL/PL, 100cm 10.90 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
Gastos de envió

mAT-40 Outdoor-Tuner for end-fed wires Nuevo

mAT-40 Outdoor-Tuner

The mAT-40 tuner has a weatherproof metal housing and is intended for permanent outdoor use. It tunes end-fed wire antennas or wire loops. A high-voltage screw terminal is provided on top of the tuner for this purpose. The connection to the radio is made via a PL coax socket on the bottom of the tuner. The power supply and control signal is provided by a waterproof screw connection, also on the bottom. A 10m long cable is included. This cable must be adapted to the respective transceiver with an optionally available interface cable. Interface cables for Icom, Kenwood and Yaesu are available. For other radios, the manufacturer offers a universal cable for own adaptation.

The following transceivers are supported:

  • with mAT-40-M cable: All Icom with 4-pin tuner socket, all devices that support AH-3 or AH-4, with modification also the IC-M710 can be used.
  • with mAT-40-K cable: All Kenwood with 6-pin tuner socket, all devices that support the AT-250 or AT-300.
  • with mAT-40-Y cable: All Yaesu with 8-pin MiniDIN CAT socket supporting the FC-30, FC-40 or FC-50.

The tuner tunes antenna wires or rods from a length of approx. 2.5m on, whereby the efficiency is strongly limited with such short antennas. The suggested antenna length is 12m, other lengths are also possible. In some cases it may be necessary to connect a counterpoise wire to the tuner. A screw terminal on the underside is used for this purpose. Here, for example, the body of a vehicle or an electric counterpoise on a sailing ship can be connected. Stainless steel brackets are included for mounting. They are used for mounting on a mast or on the wall. M6 U-bolts from 25 to 100mm width can be used for mast mounting (not included). The tuner is weatherproof.

Operation is via the "Tune" button on the radio. This simplifies the tuning process by automatically switching to low power and CW, as well as switching back to the previously used transmission line and mode. The maximum transmission power may be 120W PEP, with RTTY and other continuous wave modes about max. 30W. The tuner tunes antennas in an impedance range from approx. 5 to 1500 Ohm.

  • Volumen de entrega
  • mAT-40 Tuner
  • mAT-40-D Data Cable, 10m
  • Mountimng Brackets, stainless steel
Articulo No.
MAT-40 Automatic Oudoor Antenna Tuner 275.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
MAT-40-D Data Cable as supplied 54.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
MAT-40-M Control Cable adaptor Icom 39.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
MAT-40-K Control Cable adaptor Kenwood 39.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
MAT-40-Y Control Cable adaptor Yaesu 39.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
40402.10 H-155 Coaxial Cable, PL/PL, 10 m 22.30 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
23041.54 U bolt M6, 54mm width, stainless steel, incl. nuts and washers 4.00 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
23041.42Z 2 pcs U bolt M6, 42mm width, galvanized, incl. nuts 1.50 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
Gastos de envió

mAT-10 QRP Tuner with battery Nuevo

mAT-10 QRP-Tuner

The mAT-10 tuner is a very compact tuner for QRP devices such as the FT-817/818. The maximum permissible transmission power is 30 W SSB PEP. The power supply is provided by two built-in LiIon batteries (type 10440), which makes the tuner a good companion for portable operations with the FT-817 or FT-818. A charger is included. The control is done via a supplied cable (8-pin MiniDIN) which is connected to the ACC connector of the FT-817/818.

Operation is via a button on the tuner. By the direct coupling between tuner and transceiver the so-called "One Touch Tune" becomes possible - the tuner switches the operating mode to CW and reduces the power, tunes and then automatically switches back to the previously set operating mode and transmission power. This makes the tuning process very comfortable. As with all mAT tuners, a tuning once found is stored in one of 16000 memories, depending on the frequency. If returning to the same frequency later, the data is read from the memory, the tuning process takes place in approx. 0.2 seconds. Due to the use of bi-stable latch relays, which keep their state without power, the power consumption is extremely low. The tuner can be switched to a bypass mode if the antenna does not require tuning on a certain band. The connectors are two BNC sockets.

Articulo No.
MAT-10 QRP Automatic Antenna Tuner for Yaesu FT-817/818 249.00 € Añadir al carro de la compra Nuevo Disponible, envio en 1 o 2 dis.
40402.50CM H-155 Coaxial Cable, PL/PL, 50 cm 10.30 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
40402.01 H-155 Coaxial Cable, PL/PL, 100cm 10.90 € Añadir al carro de la compra Disponible, envio en 1 o 2 dis.
Gastos de envió