Yaesu Repeater components

Yaesu DR-1XE FM/C4FM relay 2m / 70cm

Yaesu DR-1XE Repeater DR-1XE Front
Yaesu DR-1XE Repeater rear side DR-1XE Rear

Yaesu offers you the dual mode repeater DR-1XE for a smooth transition from traditional FM mode to digital C4FM modulation. This relay is capable of both operation modes, the automatic mode select (AMS) recognizes the signal as C4FM digital or conventional FM and then the DR-1XE repeater retransmits the signal using the preset communications mode. This makes operating in FM as well as C4FM with only one relay possible.

The DR-1XE relay is shipped as a professional 19" system, an extrnal power supply (13.8V, 15A) is required. The repeater can be used either on 2m (144-146MHz) or 70cm (430-440MHz). Programming is done very comfortably via a large, coloured touch display on the front. With that you can program 'Id' (call sign), transmission and receiving frequency, transmission power (5, 20 or 50W), CTCSS, squelch and the automatic modulation select (AMS). Frequencies can be adjusted in 5 or 6.25 kHz steps.

The device requires 13.8V, max. 15A for operation. The DC cable is included. The repeater has an internal loudspeaker for local checking, also a microphone can be plugged in for testing the transmitter.

The DR-1XE repeater has no diplexer built-in, but needs be added externally. On the rear side there are separate connectors for transmission and receiving antenna available. The transmission power can be adjusted to 5, 20 or 50W. The relay identifier can be transmitted via voice or CW output in adjustable time intervals to meet regulatory requirements for automatic operating units.

  • DR-1XE includes in delivery:
  • DR-1XE relay in a 19" chassis
  • DC cable
  • English manual
  • SCU-20 PC-ACC cable (USB)
Technical Data DR-1XE
Function Value
Frequency 144-146MHz, 430-440MHz
Channel Steps 5/6.25 kHz
Antenna Impedance 50 Ω
Power Supply 13.8V, max. 15A
Power Consumption 1.5 A (Receive)
13 A (50 W TX, 144 MHz band)
14 A (50 W TX, 430 MHz band)
Operating Temperature -20 °C to +60°C
Dimensions 483 mm × 89 mm × 38 mm (B×H×T)
Weight 10 kg
TX Power 5/20/50 W
Antenna Connector N female
Modulation F1D, F2D, F3E
Reactance modulation F7 W 4FSK (C4FM)
Spurious Emissions < 60 dBc
Frequency Stability ±2.5 ppm (-20 °C to +60°C)
Type Double Super Heterodyne
Intermediate Frequencies 1st: 47.25 MHz, 2nd: 450 kHz
RX Sensitivity 0.3 µV (Digital 2 m/70 cm) BER 1%
0.2 µV (FM 2 m/70 cm) 12 dB SINAD
Antenna Connector N female
Neighbour Channel Supression < 65 dBc (typ., 20 kHz offset)
Channel Selectivity FM 12 kHz/35 kHz (-6 dB/-60 dB)
Intermodulation < 65 dB (typ., 20 / 40 kHz offset)
Audio Output 4 W (4 Ω, THD 10%, 13.8 V; internal speaker)

This device is not available anymore. We show it here for orientation purposes and to show the still available accessories.

Accessories DR-1XE

Order No.
CT-174 Data cable Mini-DIN 10pin-10pin 27.20 € Add to shopping cart
CT-175 Data cable Mini-DIN 10pin-6pin 23.40 € Add to shopping cart
DR-1XE-CABLE DR-1XE Upgrade cable set 59.00 € Add to shopping cart
FVS-2 YAESU Sprachmodul 24.50 € Add to shopping cart
HRI-200 YAESU Internet Link Adapter 109.00 € Add to shopping cart
MH-48A6J DTMF-Mikrofon 46.30 € Add to shopping cart
Info freight charges

HRI-200 Internet Link Adapter


With the HRI-200 the Yaesu C4FM-Devices like the FTM-400 or the DR-1XE or DR-2XE can be connected to the internet. The required software and the device cables are included. The HRI-200 can control 2 transceivers at the same time and can monitor 4 frequencies.
The HRI-200 interface supports the full functionality of Wires-X as the networking of the Group Monitor, Local Info, emergency ...
Even on older devices the HRI-200 can be used. Here the interface is then operated only in FM mode and controlled via DTMF. The features are significantly limited.

The connection between the HRI-200 and a computer is handled by the supplied USB cable. An additional power supply is not necessary. The necessary router configuration is handled by the UPnP protocol in the router itself.

  • In scope of delivery included:
  • HRI-200 Interface
  • Datacable Mini-DIN 10 Pin (CT-174)
  • Datacable Mini-DIN 6 Pin (CT-175)
  • Wires-X Software (CD)
  • Manual (Englisch)
  • Warranty Card
  • System Requirements for the HRI-200:
  • OS: Windows Vista/7/8/8.1
  • CPU: min. 2GHz
  • HDD: min. 1GB free disk space
  • RAM: min. 2GB
  • USB: Full-Speed USB (USB-2)
  • Screen Resolution: min. 1366x768 or more, 16bit or more
  • LAN-Port: mind. 100MBit
  • Internet Connection: min. 8 Mbps or faster
Order No.
HRI-200 Yaesu Internet Link Adapter 109.00 € Add to shopping cart
CT-174 Data cable Mini-DIN 10pin-10pin 27.20 € Add to shopping cart
CT-175 Data cable Mini-DIN 10pin-6pin 23.40 € Add to shopping cart
Info freight charges